Solving Operational Problems; Problem Solving Steps; Service Data Record - Fulgor Milano F4SP30 1 Serie Manual De Uso

Before calling for service, check the following to avoid unnecessary service charges.
Oven Problem
E008 Error appears
in the display window.
Other E Error appears in
the display window.
The oven display stays
OFF
Cooling fan continues to
run after oven is turned off
Oven door is locked and
will not release, even after
cooling
Oven is not heating
Oven is not cooking evenly
Oven temperature is too
hot or too cold
Oven light is not working
properly
Oven light stays on
Cannot remove lens cover
on light
Oven will not Self-Cleaning
properly
Clock and timer are not
working properly
Excessive moisture
Porcelain chips

Service Data Record

For authorized service or parts information see paragraph "Warranty .."
The location of the serial tag on the product can be seen when the oven door is opened. It is located on the left side, FHQWHUHG YHUWLFDOO\ MXVW LQVLGH WKH RYHQ FDYLW\ 6HH 3DJH  1RZ LV D JRRG WLPH WR ZULWH WKLV LQIRUPDWLRQ LQ WKH VSDFH
below provided. Keep your invoice for warranty validation.
0RGHO 1XPEHU BBBBBBBBBBBB 6HULDO 1XPEHU BBBBBBBBBBBBBBBB 'DWH RI ,QVWDOODWLRQ RU 2FFXSDQF\ BBBBBBBBBBBBBBB
30

Solving Operational Problems

Problem Solving Steps

A problem with latch mechanism occurred. Remove power and turn it back on again after
a few seconds. The oven should run a latch auto–test. If condition persists, note the code
number and call an authorized service center.
Remove power and turn it back on again after a few seconds. If condition persists, note
the code number and call an authorized service center.
Turn off power at the main power supply (fuse or breaker box). Turn breaker back on. If
condition persists, call an authorized service center.
7KH IDQ WXUQV RII DXWRPDWLFDOO\ ZKHQ WKH HOHFWURQLF FRPSRQHQWV KDYH FRROHG VXI¿FLHQWO\
Turn the oven off at the circuit breaker and wait a few seconds. Turn breaker back on.
The oven should reset itself and will be operable.
Check the circuit breaker or fuse box to your house. Make sure there is proper electrical
power to the oven. Make sure the oven temperature has been selected.
Check oven calibration. Adjust calibration if necessary (see To Set Temperature,
Page 15). Refer to cook charts for recommended rack position. Always reduce recipe
temperature by 25 °F (15 °C) when baking with Convention Bake mode.
The oven thermostat needs adjustment. See Calibrating Oven Temperature, Page 15.
Replace or reinsert the light bulb if loose or defective. See Page 28. Touching the bulb
ZLWK ¿QJHUV PD\ FDXVH WKH EXOE WR EXUQ RXW
Check for obstruction in oven door. Check to see if hinge is bent or door switch broken.
There may be a soil build-up around the lens cover. Wipe lens cover area with a clean dry
towel prior to attempting to remove the lens cover.
Allow the oven to cool before running Self-Cleaning. Always wipe out loose soils or heavy
spill-over before running Self-Cleaning. If oven is badly soiled, set oven for a four-hour
Self-Cleaning. See Preparing the Oven for Self-Cleaning, Page 23 to 24.
Make sure there is proper electrical power to the oven. See the Clock and Timer sections
on Page 10.
:KHQ XVLQJ %DNH PRGH SUHKHDW WKH RYHQ ¿UVW &RQYHFWLRQ %DNH DQG &RQYHFWLRQ 5RDVW
will eliminate any moisture in oven (this is one of the advantages of convection).
When oven racks are removed and replaced, always tilt racks upward and do not force
them to avoid chipping the porcelain.
Use & Care Manual
ENGLISH