Idiomas disponibles
Idiomas disponibles
TOF-50 & TOF-50 R RELEASE AGENTS SPRAY GUN
EN
5.
Unscrew needle packing set (6) by flathead screwdriver.
(Ask to authorized service center for purchasing of
optional tool.)
7.
REVERSE THE PROCEDURE TO ASSEMBLE
6. PROBLEMS CAUSES AND REMEDIES
PROBLEM
CAUSE
Fluid adj. knob (12) closed.
SPRAY GUN
Tip hole of nozzle obstructed.
DOES NOT SPRAY
Needle packing too thighten.
Air escapes from fluid nozzle (5) and
tapered seat of gun body.
INTERMITTENT
Air escapes from fluid passages because
SPRAY PATTERN
O'ring is worn out.
Air escapes from fluid hose joint.
Dirty nozzle (5) or air cap set (2).
Nozzle (5) or air cap (2) has been damaged.
Fluid nozzle (5) is loose or not property
fitted.
DEFECTIVE
Release agent viscosity too high or too
SPRAY PATTERN
low.
Release agent output too high or too low.
Fluid nozzle (5), needle set (5-1) or gun
body, dirty, damaged or worn on seat.
Fluid nozzle (5) and gun body are loose.
Fluid needle (5-1) set is loose.
Fluid neeedle spring (10) is worn.
LEAKING
Needle packing set (6) dirty or too tighten. Check or adjust.
Needle packing set (6) worn or too loose.
Piston set (9) is dirty.
Piston O'ring is worn.
6
6.
Remove fluid nozzle (5) air cap (2), air cap packing (3), and
cover ring (4).
CAUTION!
REMEDY
Check and adjust it.
Check and clean it.
Check and adjust it.
Check , clean & replace if
necessary.
Replace O'ring.
Tighten.
Clean carefully.
Replace if damaged.
Tighten or remove and clean its
seated section.
Dilute paint or increase vis-
cosity.
Adjust fluid adj. knob (12) to
reduce or increase.
Clean & replace if necessary.
Tighten.
Tighten.
Replace.
Replace or retighten.
Clean or replace O'ring if
necessary.
Replace.
TOF-50 & TOF-50 R RELEASE AGENTS SPRAY GUN
6.1 INSPECTION AND REPLACEMENT STANDARD
WHERE TO INSPECT
Each hole passage of air cap set (2) and fluid nozzle set
(5).
Packings and O'rings.
Leakage from seat section between fluid nozzle
(5) and piston (5-1).
7. SPARE PARTS LIST
Round Pattern
option 22
4-1
2-1
5
2
3
4
19
25
18
26
27
REF.
DESCRIPTION
1
BODY
2
AIR CAP SET
2-1
AIR CAP SET (ROUND PATTERN)
3
PACKING
4
COVER RING
4-1
PROTECTION COVER
5
FLUID NOZZLE SET
5-1
FLUID NEEDLE SET
6
NEEDLE PACKING SET
9
PISTON ASSY
9-1
O RING
9-2
O RING
10
FLUID NEEDLE SPRING
11
PISTON SPRING
REPLACEMENT PART
Replace air cap or fluid nozzle if they are crushed or de-
formed.
Replace if deformed or worn out.
Replace them if there is any leakage even after cleaning.
option 28
14
13
9
6
9-1
9-2
1
5-1
10
11
17
12
13
15
20
15
option
22
28
REF.
DESCRIPTION
12
FLUID ADJ. ASSY
13
HEXAGON NUT
14
PATTERN ADJ. SET
15
HOSE NIPPLE
17
TRIGGER STUD
18
TRIGGER
19
E STOPPER
n
20
PUSHING BAR
n
25
E STOPPER
n
27
HEXAGON WRENCH
28
BRUSH
n
22 Opt.
HOOK SET
n
28 Opt.
PLUG
Marked parts are wearable parts.
n
EN
7
