Idiomas disponibles
Idiomas disponibles
deemed a misuse of the device. The user shall be solely liable
for improper use of the device.
Grounding installation
This appliance is classified as protection class I and must be
connected to a protective ground. Grounding reduces the risk
of electric shock by providing an escape wire for the electric
current.
This appliance is fitted with a power cord with grounding plug
or electrical connections with grounding wire. The connections
must be properly installed and grounded.
Main parts of the product
(Fig.1 on page 3)
1. Internal wires of power cord: Connection with the electrical
wires from the power system
2. Hooking hole: Hanging the lamp to the ceiling
3. Rotating knob: Adjusting the power cord length
4. Cap cover: Fix the length of the power cord after setting
5. ON (|) / OFF (0) switch: Switch ON / OFF the lamp
6. Lamp shade: Control the direction of the light
Remark: The content of this manual applies for all listed items
unless specified otherwise. The appearance may vary from the
shown illustrations.
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
• Multiple installations of the lamps must have a minimum
distance of 40 cm between centre of the shade of each unit.
Preparation before installation
CAUTION! Before installation, check the appliance to make
sure there is no damage. CLOSE the electrical power circuit
system & switch OFF the appliance before starting installation
work.
ATTENTION! Installation work should be carried out by quali-
fied electrician. Contact your local authority for advice if have
question. DO NOT attempt to install, repair and maintenance
by yourself.
• Verify prior to installation that the ceiling can safely support
the appliance.
• Make sure that no electrical wires, water pipes, gas pipes or
other lines are located around the installation location.
• Consult a qualified contractor for assistance about the struc-
ture of the ceiling. This is to ensure that the installation is car-
ried out properly and safely.
• Switch OFF the appliance by pressing the ON (|) / OFF (0)
switch on the appliance at the "0" position.
ATTENTION! Before starting the installation, make sure you
have all the tools such as screwdriver, electric drills, measur-
ing tape, marking pencil, wall anchors, wiring nuts, mounting
bracket with hook, etc. (All are not supplied) and make sure
they are well functioning.
Instruction for installation
ATTENTION! Make sure again all the electrical power system
circuit is CLOSED and the ON (|) / OFF (0) switch of the appli-
ance is at the OFF (0) position.
A) Installation of the mounting bracket with hook (Not includ-
ed).
• Secure the mounting bracket with screws and wall anchors
provided.
• Feed the electrical wires from the ceiling through opening of
the mounting bracket.
B) Assemble the appliance with the hook.
• You can extend the power cord by twisting the cap cover if
the internal wires of power cord are too short for connection.
• Please make sure the wires are connected to the correspond-
ing wires terminal of the power circuit system. The wires of
the power cord are coloured as below:
a) Blue = Neutral (N)
b) Brown = Live (L)
c) Green and yellow = Earth (E)
• Wrap the connected wires together with the electrical insula-
tion tape or wiring nuts (Both are not included).
• Hang the hole of the appliance with the hook as provided on
the mounting bracket. (Not supplied).
IMPORTANT! Please make sure the appliance is secure and
correctly connected after installation.
Operating instructions
ATTENTION! Make sure the electrical power system circuit of
ceiling is CLOSED and switch OFF the hanging lamp at the "0"
position.
• First, screw in clockwise direction the shatterproof lamp (sup-
plied) securely inside the lamp holder.
• This appliance has a retractable power cord to about 150 cm
that allows the lamp height to be adjusted. Rotate the rotating
knob to set the length of the power cord as desired.
• Then, pull gently straight down on the shade to extend the
cord until the desired height is reached.
• Next, open the electrical power system circuit and switch ON
the appliance by pressing the ON (|) / OFF (0) switch to the
"|" position.
• Now, the lamp is light up and keep food warm process is
started.
CAUTION! RISK OF BURNS! HOT SURFACE! The lamp
•
shade surface is very hot during use. Do not touch it.
Switch OFF the lamp & cool down before setting the cord
length.
• IMPORTANT! Remember to keep at least 30cm distance from
the lighted bulb.
GB
9
