Idiomas disponibles
Idiomas disponibles
2 609 140 541.book Seite 17 Dienstag, 22. Januar 2008 8:46 08
Readjusting the Clamping Lever
To readjust the tightening tension, open the
clamping lever 10, turn the nut of the clamping
lever approx. 45° in clockwise direction using an
open-end spanner and then lock the clamping
lever 10 again. Check if the motor unit 1 is
clamped securely. Do not over tighten the nut.
Starting Operation
Observe correct mains voltage: The voltage
of the power source must agree with the voltage
specified on the nameplate of the machine.
Equipment marked with 230 V can also be con-
nected to 220 V.
Switching On and Off
To start the machine, set the On/Off switch 11
to I.
To switch off the machine, set the On/Off
switch 11 to 0.
Setting the Depth-of-cut
(see figure
)
F
The adjustment of the depth-of-cut may only
be carried out when the trimmer is switched
off.
Place the trimmer on the workpiece to be
worked.
Open the clamping lever 10, set the " " mark
on the routing base 2 to the "
slowly lower the motor unit until the router
touches the workpiece. Fix the motor unit in this
position by locking the clamping lever 10.
Read the measuring value off the scale 8 and
note it down (zeroing). Add the desired depth-of-
cut to this value.
Open the clamping lever 10 and set the motor
unit to the calculated scale value. Set the
" " mark on the routing base 2 to the " " sym-
bol and lock the clamping lever 10 again.
Check the carried out depth-of-cut adjustment
with a trial cut and correct it, if necessary.
For fine adjustment of the depth-of-cut, set the
" " mark on the motor unit to the " " symbol
with the clamping lever 10 open. Adjust the de-
sired depth-of-cut with the thumbwheel 3. After-
wards, lock the clamping lever 10 to securely
lock the motor unit in the routing base.
2 609 140 541 • 22.1.08
Operating Instructions
Direction of Feed (see figure
The feed motion of the router must always be
carried out against the rotation direction of the
router bit (up-grinding).
When routing in the rotation direction of the
router bit (down-cutting), the machine can break
loose, eliminating control by the user.
Routing Process
Use the machine only with the routing
base mounted. Loss of control over the ma-
chine can cause injuries.
Before beginning the routing procedure,
check if the " " mark on the routing base 2 is
positioned in line with the " " symbol on the
motor unit 1.
Note: Take into consideration that the router
bit 4 always extends out of the base plate 7. Do
not damage the template or the workpiece.
Adjust the depth-of-cut as described previously.
Switch the machine on and guide it to the loca-
tion subject to working.
Carry out the routing procedure applying uni-
form feed.
Switch the machine off after finishing the routing
process. Do not place the power tool down until
after the router bit has come to a complete stop.
Routing with Guide Bushing
" symbol and
The guide bushing 14 enables template and
pattern routing on workpieces.
Inserting guide bushing 14 (see figure
Unscrew the four fastening screws on the bot-
tom side of the guide plate 6 and remove the
guide plate 6. Insert the rubber ring 15 and then
the guide bushing 14 into the round guide
plate 16 as shown in the figure. Screw the round
guide plate 16 to the base plate 7 with the coun-
tersunk screws provided.
Adjusting/centring the guide bushing
(see figure
To ensure that the distance from router bit cen-
tre and guide bushing edge is uniform, the guide
bushing and the guide plate can be adjusted to
each other, if required.
Loosen the fastening screws 17 by approx.
2 turns so that the round guide plate 16 can be
moved freely.
G
I
)
English | 17
)
H
)
