Johnson GreenBrite JLN300-GN3360 Guia De Inicio Rapido

Quick Start Guide: Model No. JLN300-GN3360 / Guide de rapide prise en mains : Modèle n° JLN300-GN3360 /
Guía de inicio rápido: N.º de modelo JLN300-GN3360
Thank you for purchasing this GreenBrite® 3x360° Plane Laser! We want to get you up and running as
quickly as possible – but this quick start guide is not a replacement for reading and understanding your
operator's manual. For complete safety and operating instructions, refer to the operator's manual.
Merci d'avoir acheté ce niveau GreenBrite® 3x360° à
laser ! Nous souhaitons que vous soyez opérationnel le
plus rapidement possible, mais ce guide de rapide prise
en mains ne remplace pas la lecture et la compréhension
de votre manuel d'utilisation. Pour obtenir des instructions
complètes sur la sécurité et l'utilisation, reportez-vous au
manuel d'utilisation.
¡Gracias por comprar este láser de 3x360° planos
GreenBrite®! Queremos que empiece a trabajar lo antes
posible, pero esta guía de inicio rápido no reemplaza la
lectura y comprensión del manual del operador. Para
conocer las instrucciones de operación y seguridad
completas, consulte el manual del operador.
CHARGING LI-ION BATTERY
1. Ensure the locking compensator is in the locked
(OFF) position.
2. Rotate the laser so the rear of the unit is
accessible.
3. Push down on the battery door lock tab to
unlock and open the battery door. Remove the
li-ion battery case from the unit.
4. Press the micro switch on the battery to check
its fuel status. See figure 1.
5. Connect a Type C, USB charger to battery
charging port located on the front of the battery
and plug the charger into a power source.
6. When all three LEDs are lit, the battery is fully
charged. Charge time is typically five hours. See
table below.
Fuel Gauge
Volt of battery <3.5V
3.5V ≤ Volt of battery <3.8V
3.8V ≤ Volt of battery
7. Reinsert li-ion battery into the unit. Be sure the end with the openings is inserted first.
LED1
Voyant 1
LED1
LED2
Voyant 2
LED2
LED3
Micro Switch
Voyant 3
Mini-interrupteur
LED3
Microinterruptor
Figure 1 / Figure 1 / Figura 1
LED1 LED2 LED3
ON OFF OFF
ON ON OFF
ON ON ON
Mounting Hole
Trou de montage
Orificio de montaje
Mounting Magnets
Aimants de montage
Imanes de montaje
Non-mar Rubber Feet
Pieds en caoutchouc
anti-marques
Patas de goma
antiarañazos
1/4"-20 Screw Thread
Filetage de vis 1/4 po-20
Rosca del tornillo 1/4"-20
Figure 2 / Figure 2 / Figura 2
MOUNTING POSITIONS
Place the unit in an upright position, either on a stable, flat surface, mount it to a tripod with a 1/4"-20
threaded screw, mount it to a ferrous surface using the magnets, or hang it on a nail using the
mounting hole. Non-mar rubber feet on the unit prevent damage to surfaces. See figure 2.
Use with the track mount for easy vertical applications. Hang the track clip to a vertical surface or
clamp the track clip to ceiling channels, racks, etc. To attach the unit to the track mount, place the
unit's magnets on the metal plate. Slide the unit up or down to adjust its position. See figure 3.
OPERATION / AUTOMATIC MODE
1. Slide the locking compensator/power switch to the left to the unlocked (ON)
on the unit. NOTE: The unit must be within ±4° of level for the self-leveling feature to function
properly. If the unit is beyond its 4° self-leveling range, the laser will not self-level, the laser will
flash, and the level indicator status light will flash red.
2. On the keypad, press the button to turn on the horizontal laser beam. Press the
turn on the right vertical laser beam. Press the
The unit can be used with any combination of laser beams turned on simultaneously.
3. When using the vertical (plumb) laser beam, rotate the unit to the desired position. Use the
fine-tuning adjustment knob to make small adjustments.
4. Slide the locking compensator to the right to the locked (OFF)
OPERATION / TILT (MANUAL) MODE
The pendulum lock secures the laser during transport to prevent damage to the self-leveling
mechanism. It also enables the laser to be used at any angle in manual mode.
1. The unit can be used to project laser beams at any angle desired, such as when projecting a line for
stairs or a railing. This mode produces the best results when the unit is mounted on a tripod. With
the locking compensator in the locked (OFF)
keypad for three seconds to power on the unit. The status lights will illuminate. The level indicator
LED will light a steady red to indicate the unit is not self-leveling.
2. On the keypad, press the button to turn on the horizontal laser beam. Press the
turn on the right vertical laser beam. Press the
The unit can be used with any combination of laser beams turned on simultaneously. Adjust the unit
to the desired angle. The lasers will not self-level.
NOTE: While in manual level mode, active lasers will flash three times, at one second intervals, every
15 seconds. This is a visual indication that the unit is in manual level mode and will not self-level.
3. When using the vertical (plumb) laser beam, rotate the unit to the desired position. Use the
fine-tuning adjustment knob to make small adjustments.
4. Press any of the laser beam buttons for three seconds to power off the unit.
Download full manual at / Téléchargez le manuel complet sur / Descargue este manual en
Ceiling Channel or Rack
Rail ou rack de plafond
Canal de techo o rack
Track Mount Release Lever
Levier de dégagement de
l'ensemble pour le
montage sur rail
Palanca de liberación
del montaje en riel
Figure 3 / Figure 3 / Figura 3
position to power
button to
button to turn on the front vertical laser beam.
position to power off the unit.
position, press and hold any of the buttons on the
button to
button to turn on the front vertical laser beam.
www.johnsonlevel.com/manuals
JLN300-GN3360
©2024 Johnson Level & Tool