Johnson GreenBrite JLD300-GN2D Guia De Inicio Rapido

Quick Start Guide: Model No. JLD300-GN2D / Guide de rapide prise en mains : Modèle n° JLD300-GN2D /
Guía de inicio rápido: N.º de modelo JLD300-GN2D
Thank you for purchasing this GreenBrite® Cross-Line & 2 Dot Laser! We want to get you up and
running as quickly as possible – but this quick start guide is not a replacement for reading and
understanding your operator's manual. For complete safety and operating instructions, refer to the
operator's manual.
Merci d'avoir acheté ce niveau GreenBrite®
Cross-Line & 2 Dot à laser ! Nous souhaitons que
vous soyez opérationnel le plus rapidement possible,
mais ce guide de rapide prise en mains ne remplace
pas la lecture et la compréhension de votre manuel
d'utilisation. Pour obtenir des instructions complètes
sur la sécurité et l'utilisation, reportez-vous au
manuel d'utilisation.
¡Gracias por comprar este láser de 2 puntos y líneas
cruzadas GreenBrite®! Queremos que empiece a
trabajar lo antes posible, pero esta guía de inicio
rápido no reemplaza la lectura y comprensión del
manual del operador. Para conocer las instrucciones
de operación y seguridad completas, consulte el
manual del operador.
CHARGING LI-ION BATTERY
1. Ensure the locking compensator is in the locked
(OFF) position.
2. Rotate the laser so the rear of the unit is
accessible.
3. Push down on the battery door lock tab to
unlock and open the battery door. Remove the
li-ion battery case from the unit.
4. Press the micro switch on the battery to check
its fuel status. See figure 1.
5. Connect a Type C, USB charger to battery
charging port located on the front of the battery
and plug the charger into a power source.
6. When all three LEDs are lit, the battery is fully
charged. Charge time is typically five hours. See
table below.
Fuel Gauge
Volt of battery <3.5V
3.5V ≤ Volt of battery <3.8V
3.8V ≤ Volt of battery
7. Reinsert li-ion battery into the unit. Be sure the end with the openings is inserted first.
LED1
Voyant 1
LED1
LED2
Voyant 2
LED2
LED3
Micro Switch
Voyant 3
Mini-interrupteur
LED3
Microinterruptor
Figure 1 / Figure 1 / Figura 1
LED1 LED2 LED3
ON OFF OFF
ON ON OFF
ON ON ON
MOUNTING POSITIONS
Place the unit in an upright position, either on
a stable, flat surface, mount it to a tripod with
a 1/4"-20 threaded screw, mount it to a ferrous
surface using the magnets, or hang it on a nail
using the mounting hole. Non-mar rubber feet on
the unit prevent damage to surfaces.
OPERATION / AUTOMATIC MODE
1. Slide the locking compensator/power switch to the left to the unlocked (ON)
on the unit. NOTE: The unit must be within ±4° of level for the self-leveling feature to function
properly. If the unit is beyond its 4° self-leveling range, the laser will not self-level, the laser will
flash, and the level indicator status light will flash red.
2. On the keypad, press the button to turn on the horizontal laser beam. Press the
turn on the vertical laser beam. Press the
used with any combination of laser beams turned on simultaneously.
3. When using the vertical (plumb) laser beam, rotate the unit to the desired position. Use the
fine-tuning adjustment knob to make small adjustments.
4. Slide the locking compensator to the right to the locked (OFF)
OPERATION / TILT (MANUAL) MODE
The pendulum lock secures the laser during transport to prevent damage to the self-leveling
mechanism. It also enables the laser to be used at any angle in manual mode.
1. The unit can be used to project laser beams at any angle desired, such as when projecting a line for
stairs or a railing. This mode produces the best results when the unit is mounted on a tripod. With
the locking compensator in the locked (OFF)
keypad for three seconds to power on the unit. The status lights will illuminate. The level indicator
LED will light a steady red to indicate the unit is not self-leveling.
2. On the keypad, press the button to turn on the horizontal laser beam. Press the
turn on the vertical laser beam. Press the
used with any combination of laser beams turned on simultaneously. Adjust the unit to the desired
angle. The lasers will not self-level.
NOTE: While in manual level mode, active lasers will flash three times, at one second intervals, every
15 seconds. This is a visual indication that the unit is in manual level mode and will not self-level.
3. Press any of the laser beam buttons for three seconds to power off the unit.
Download full manual at / Téléchargez le manuel complet sur / Descargue este manual en
Mounting Hole
Trou de montage
Orificio de montaje
Mounting Magnets
Aimants de montage
Imanes de montaje
Non-mar
Rubber Feet
Pieds en caoutchouc
anti-marques
Patas de goma
antiarañazos
1/4"-20 Screw Thread
Filetage de vis 1/4 po-20
Rosca del tornillo 1/4"-20
position to power
button to
button to turn on the dot laser beam. The unit can be
position to power off the unit.
position, press and hold any of the buttons on the
button to
button to turn on the dot laser beam. The unit can be
www.johnsonlevel.com/manuals
JLD300-GN2D
©2024 Johnson Level & Tool