Idiomas disponibles
Idiomas disponibles
MODEL: PMPN
O Do
not
drive
fasteners
on
top
of other
fasteners or with the tool at an overly steep
angle
as
this
may
cause
deflection
of
fasteners which could cause injury.
6 Do not actuate the tool unless you intend to
drive a fastener into the workpiece.
@ Always handle the tool with care:
Respect the tool as a working implement.
© Never engage in horseplay.
© Keep others a safe distance from the tool
while tool is in operation as accidental
actuation may occur, possibly causing injury.
AIR SUPPLY AND CONNECTIONS
O The connector on the tool must not hold
pressure when
air supply is disconnected.
If
an incorrect fitting is used, the tool can remain
charged with air after disconnecting and thus will
be able to drive a fastener even after the air line is
disconnected, possibly causing injury.
@ Do
not
use
any
type
of reactive
gases,
including,
but
not
limited
to, oxygen
and
combustible
gases, as a power source.
Use
filtered, lubricated, regulated compressed air only.
Use of a reactive gas instead of compressed air
may cause the tool to explode which will cause
death or serious personal injury.
REEMAN
@ Use only a pressure-regulated
compressed
air
source to limit the air pressure supplied to the
tool. The regulated pressure must not exceed 100
psi. If the regulator fails, the pressure delivered to the
tool must not exceed 200 psi. Over pressurizing the
tool is able to result in bursting, abnormal operation,
breakage of the tool or serious injury to persons. Use
only clean, dry, regulated compressed air at the rated
pressure
or within
the
rated
pressure
range
as
marked on the tool. Always verify prior to using the
tool that the air source has been adjusted to the rated
air pressure or within the rated air-pressure range.
O Always disconnect air resource:
< Before unloading or making adjustments.
@ When maintaining the tool.
@ When clearing a jam.
@ When touching the safety yoke.
@ When tool is not in use.
© When moving to a different work area.
Such precautionary measures reduce the risk of injury
to persons.
SAVE THESE INSTRUCTIONS
LOADING TOOL
@ Do not load the tool with fasteners when any one
of the operating controls is activated.
O Never
place
a hand
or any
part of body
in
fastener discharge area of tool.
@ Never point tool at anyone.
08
HTTP://WWW.
FREEMANTOOLS.
COM
1-888-669-5672
MODEL: PMPN
workpiece
contact
as
accidental
actuation
may occur, possibly causing injury.
A WARNING:
The
warnings
and
precautions
discussed
above cannot cover all possible conditions
and situations that may occur. It must be
understood by the user that common sense
and caution
are factors which
cannot
be
built into this product, but must be supplied
by the user.
UNPACKING
@This
tool
has
been
shipped
completely
assembled.
@ Make sure that all items listed in the packing
list are included.
@ Carefully remove the tool and any accessories
from the box.
@ Inspect the tool carefully to make
sure
no
breakage or damage occurred during shipping.
@ Do not discard the packing material until you
have
carefully
inspected
and
satisfactorily
operated the tool.
REEMAN
@Do
not pull the trigger or depress the
@[If any parts are damaged or missing, please call 1-
888-669-5672.
A WARNING:
If any parts are missing do not operate this tool
until the missing parts are replaced. Failure to
do so could result in possible serious personal
injury.
A WARNING:
Do not attempt to modify this tool or create
accessories
not recommended
for use with
this tool. Any such alteration or modification is
misuse
and
could
result
in
hazardous
condition leading to possible serious personal
injury.
SPECIFICATIONS
AIR INLET: 1/4 inch NPT
WEIGHT: 1.38 lb
2
| [Sam
MAXIMUM PRESSURE: 100 psi
à. |] oom
PRESSURE RANGE: 80 psi- 100 psi
||
PIN SIZE RANGE: 2 inch to 4 inch
0:1137 0:192
(02.87 -4.87mm)
HTTP://WWW.
FREEMANTOOLS.
COM
1-888-669-5672
