Maintenance And Service; Connectivity Functions; Maintenance And Cleaning - Bosch Professional GBH 18V-24 C Manual Original

24 | English
the SDS plus drilling tool can lead to incorrect adjustment
of the drilling depth.
– Pull the depth stop far enough out that the distance
between the drill bit tip and the edge of the depth stop
corresponds to the required drilling depth X.
Overload clutch
If the application tool jams or snags, the power trans-
u
mission to the drill spindle will be interrupted. Always
hold the power tool firmly with both hands to with-
stand the forces this may create and adopt a position
with stable footing.
Switch the power tool off immediately and remove the
u
application tool if the power tool becomes blocked.
Switching on when the drilling tool is blocked may
cause high torque reactions.
Rapid shut-off (KickBack control)
The rapid shut-off function (KickBack Control)
gives the user greater control over the power
tool and offers them better protection than
power tools that do not have KickBack Control.
If the power tool suddenly and unforeseeably
rotates around the drilling axis, it will switch off, the rapid
shut-off indicator (19) will light up red and the worklight
(12) will flash. When rapid shut-off is activated, the status
indicator (17) flashes red.
– To switch the tool back on, release the on/off switch (9)
and then press it again.
Inserting screwdriver bits (see figure F)
Only apply the power tool to the screw/nut when the
u
tool is switched off. Rotating tool inserts can slip off.
A universal holder (24) with SDS plus shank is required to
work with screwdriver bits.
– Clean and lightly grease the insertion end of the shank.
– Insert the universal holder into the tool holder while turn-
ing it until it locks automatically.
– Check that it is locked by pulling the universal holder.
– Insert a screwdriver bit in the universal holder. Only use
screwdriver bits that fit the screw head.
– To remove the universal holder, slide the locking sleeve
(4) backwards and remove the universal holder (24)
from the tool holder.

Connectivity functions

System Requirements for Using the App
System Requirements
Mobile device (tablet,
smartphone)
Installing and Setting up the App
You will need to install the device-specific app before you
can use the connectivity functions.
1 609 92A 9EW | (22.05.2024)
– Download the app from the corresponding app store
– The display of your mobile device shows you all of the
Data Transfer via Bluetooth
The built-in Bluetooth
regular intervals. Depending on ambient conditions, multiple
transmission intervals may be required before the power
tool is detected. If the power tool is not detected, check the
following:
– Is the distance to the mobile device too great?
– Is the coin cell for the built-in Bluetooth
– Switch Bluetooth
Functions in Conjunction with the Power Tool
In conjunction with the Bluetooth® Low Energy Module , the
following connectivity functions are available for the power
tool:
– Registration and personalisation
– Status check, output of warning messages
– General information and settings
– Management
– Adjusting the Bluetooth

Maintenance and Service

Maintenance and Cleaning

u
Android 6.0 (and newer)
u
iOS 11 (and newer)
u
– Clean the tool holder (2) after each use.
(Apple App Store, Google Play Store).
Note: You will need to have a user account with the relev-
ant app store to do this.
App name
BeConnected
PRO360
subsequent steps required to connect the power tool to
the mobile device.
®
®
Low Energy Module sends a signal at
Reduce the distance between the mobile device and the
power tool.
ule weak or drained?
Contact an authorised after-sales service centre for
Bosch power tools to replace the coin cell.
®
off and on again on your mobile device.
Check whether the power tool has now been detected.
®
transfer settings for Favourite
working mode
Before carrying out any work on the power tool (e.g.
maintenance, tool change etc.), remove the battery
from the power tool. There is risk of injury from uninten-
tionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.
Replace a damaged dust protection cap immediately.
It is recommended that you have use an after-sales
service for this.
iOS/Android
®
Low Energy Mod-
Bosch Power Tools