Idiomas disponibles
Idiomas disponibles
safer performance.
•
Follow steps outlined in this manual to sharpen chain.
•
Keep handles dry, clean, and free of oil and grease.
•
Keep all screws and nuts tight.
•
Keep battery pack from heat, oil, and sharp edges.
4. When servicing, use only identical replacement
parts.
5. When not in use, always store chain saw
•
in a high or locked place, out of children's reach
•
in a dry place
•
with Bar and Chain Storage/Transportation Cover (9) in
place
Bar Maintenance
To maximize bar life, the following bar maintenance is
recommended.
The bar rails that carry the chain should be cleaned before
storing the tool or if the bar or chain appear to be dirty.
The rails should be cleaned every time the chain is removed.
To clean the Bar rails:
1. Remove chain cover and bar and chain. (see section
ASSEMBLY)
2. Using a wire brush, screwdriver or similar tool, clear the
residue from the inner groove of the bar (See Fig. M).
3. Make sure to clean oil passages thoroughly
Conditions which require Chain (7) and Guide Bar (6)
maintenance:
•
Saw cuts to one side or at an angle.
•
Saw has to be forced through the cut.
•
Inadequate supply of oil to the bar and chain.
Check the condition of the guide bar each time the chain
is sharpened. A worn guide bar will damage the chain and
make cutting difficult.
20
After each use, with unit disconnected from power source,
clean all sawdust from the guide bar and sprocket hole.
When rail top is uneven, use a flat file to restore square
edges and sides.
File Rail Edges
and Sides
Square
Worn Groove
Replace the guide bar when the groove is worn, the guide bar
is bent or cracked, or when excess heating or burring of the
rails occurs. If replacement is necessary, use only the guide
bar specified for your saw in the repair parts list or on the
decal located on the chain saw.
Replacing Bar & Chain
Replace chain when cutters are too worn to sharpen or
when chain stops. Only use replacement chain noted in this
manual.
Inspect Guide Bar before sharpening chain. A worn or damaged
Guide Bar is unsafe. A worn or damaged Guide Bar will damage
chain. It will also make cutting harder.
Fit the Bar Tensioning Plate (23) Tab into the new bar by
tightening the screw clockwise. The tab protrusion (a) must
be fitted into the bar hole. (See Fig N)
SHARPENING SAW CHAIN
WARNING: Remove the battery pack before
servicing. Severe injury or death could occur
from electrical shock or body contact with
Cordless Chain Saw
moving chain.
Cutting edges on chain are sharp. Use protective
gloves when handling chain.
Keep chain sharp. Your saw will cut faster and more safely.
A dull chain will cause undue sprocket, guide bar, chain, and
motor wear. If you must force chain into wood and cutting
creates only sawdust with few large chips, chain is dull.
LUBRICATE SPROCKET
WARNING: Wear heavy duty gloves when
performing any maintenance or service to this
tool. Always remove the battery pack before
performing any service or maintenance on this tool.
NOTE: It is not necessary to remove the chain or bar when
lubricating the guide bar sprocket.
1. Clean the bar and sprocket
2. Using a grease gun, insert the tip of the gun into the
lubrication hole and inject grease until it appears at the
outside edge of the sprocket tip (See Fig. O).
3. To rotate the sprocket pull the chain by hand until the
ungreased side of the sprocket is in line with the grease
hole. Repeat the lubrication procedure.
ENVIRONMENTAL
PROTECTION
Waste electrical products must not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authorities or retailer for
recycling advice.
FOR BATTERY TOOLS
The ambient temperature range for the use and
storage of tool and battery is 0°C-45°C.
The recommended ambient temperature range for
the charging system during charging is 0°C-40°C.
Correct Groove
EN
