Idiomas disponibles
Idiomas disponibles
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched off and times in which
the tool is switched on but operates without load).
5. Before starting the equipment
Warning!
Always remove the battery/batteries before
making adjustments to the equipment.
The garden chipper/shredder is delivered
unassembled. The chassis and the wheels
must be fi tted before use. Follow the operating
instructions step-by-step and use the pictures
provided as a visual guide to easily assemble the
machine.
5.1 Assembling the chassis, axles and
wheels (Fig. 3-11)
•
Pull the hex. key (19) out of the hex. key
holder (29).
•
Place the motor housing upside down on the
floor.
•
Push the rear axle (7) and the front axle (8)
through the left chassis (5) and the right
chassis (6).
•
Fit the sleeves (22) and the wheels (4) on
both sides.
•
Push a screwdriver (24) through the holding
hole of the rear axle (7) and secure with the
washers (21) and with the screws (20) as
shown in Fig. 7.
•
Fit the wheel caps (9) on the wheels; make
sure that the clips (23) on the wheel caps
latch into the recesses on the wheels as
Anl_Redaxxo_36_25_SPK7_NA.indb 12
Anl_Redaxxo_36_25_SPK7_NA.indb 12
EN
shown in Fig. 8.
•
Push a screwdriver (24) through the holding
hole of the front axle (8) and secure with the
washers (21) and with the screws (20) as
shown in Fig. 9.
•
Insert the assembled chassis into the
provided openings as far as it will go.
•
Use the washers (17) and the screws (18) to
secure the chassis to the motor housing as
shown in Fig. 11.
5.2 Paddle holder (Fig. 12)
Push the paddle (Item 10) into the paddle holder
(Item 25).
5.3 Inserting the hex. key into the holder (Fig.
13-16)
•
Swing open and remove the loading funnel
(Fig. 13 / Item 2) by opening the release knob
(Fig. 13 / Item 12).
•
Push the hex. key (Fig. 14 / Item 19) into the
hole provided for it in the ejector housing.
•
Insert the loading funnel (Fig. 15 / Item 2) into
the hooks on the ejector housing and swing
the housing shut.
•
Check that the loading funnel (Fig. 16 /
Item 2) is correctly seated and retighten the
release knob (Fig. 16 / Item 12).
Note: The hex. key can be used to loosen the
blade screws.
5.4 Fitting the batteries (Fig. 17)
Note: The battery cover (Item 3) is self-closing
and is kept shut by magnets.
Open the battery cover. Push the two batteries
into the battery mounts. Make sure that the
pushlock button (Item 30) latches in place as
soon as the battery has been pushed fully in. To
remove the batteries, proceed in reverse order.
Important!
The equipment's operating time depends on
the battery with the lower charge level or lower
capacity (Ah). Therefore, only use rechargeable
batteries which are charged to the same level and
have the same capacity (Ah). Never combine full
and half-full batteries or batteries with diff erent
capacities (Ah).
Always charge the two batteries simultaneously
before starting to use them.
Batteries with a capacity rating of 4.0 Ah or higher
are recommended for the best performance.
- 12 -
20.11.2023 09:59:17
20.11.2023 09:59:17
