Idiomas disponibles
Idiomas disponibles
GB
CONTROLS:
Push button with warning light for turning
INTERNAL LIGHTS on or off
Push button with warning light for turning
EXTERNAL LIGHT on or off
Push button:
- to view the values of the batteries and tanks
- to turn off the control panel
- to activate the night function
SCREENS:
This symbol indicates that the control panel is turned on.
See also CONSUMPTION and the nocturnal settings function
The warning light goes on when the 230V mains is connected.
The warning light goes on when
of the 230V mains when the two batteries are in parallel verifing before the battery service voltage.
The warning light goes on when the recycling tank R1 is full.
Press the push button repeatedly for viewing:
-The voltage on the car battery B1
-The voltage on the service battery B2
-The level percentage % (0, 25, 50, 75, 100) of the reservoir S1
-The % of remaining car battery autonomy.
-The % of remaining service battery autonomy.
The display remains on the screen for 30 seconds.
The battery level percentage is not shown when charging via battery charger or when the vehicle is in motion; in
these cases, it is replaced by moving segments.
If there is a problem with the tank level sensor, the display shows three dash lines [ - - - ].
ALARMS:
Batteries: Car battery (B1) less than 11,8V or Service battery (B2) less than 10,5V.
In this case there is a bleep (if enabled) and the flashing battery symbol that have generated the alarm
(for the first 30 seconds you see the value).
:
Tanks
Tank S1 empty or Recovery tanks R1 full.
In this case there is a bleep (if enabled) and the flashing symbol the corresponding tank that raised the alarm
(for the first 30 seconds you see the value).
This symbol appears on the display to indicate that the 230V mains supply on with the vehicle in motion.
:
In this case a continuous acoustic alarm sounds. If the panel is off, only the continuous acoustic alarm is activated.
:
This symbol appears when there is an error communicating with NE185/NE196 shunt.
SETTING:
Hold down the
push button for over 3 seconds to disable (display shows "
low battery alarm.
Hold down the
push button for over 3 seconds to disable (display shows "
confirmation beep button pressed, and alarm buzzers.
Hold down the
push button for over 3 seconds to disable (display shows "
alarm of tank S1.
Hold down the
push button for over 3 seconds, the display will show the panel firmware version for one second and then
the firmware version for the shunt in use for a further second.
SHUTDOWN / NIGHT FUNCTION
Hold down the push button for over 3 seconds the display shows the writing OFF:
- if the button is released, the panel switches off.
- If the button remains pressed for another 5 seconds, the display shows the writing
is enabled.
In the night function all the symbols are switched off, only the
automatic shutdown control is managed. Press any button to light the symbols that have been turned off.
CONSUMPTION:
To turn on the control panel you must touch for 2 sec. a button any.
On stand by (no active controls) the control panel with shunt NE185/NE196 consumes a total of approx 33mA.
Turning off the control panel reduces the total consumption to just 3mA.
AUTO-
SHUTDOWN
:
If the service battery voltage drops below 10,5V, after 3 minute the control panel turns itself off, together with all live parts. In
this case is advisable to disconnect all loads with the battery main switch and recharge the battery services within 2 days.
WARNING: If the vehicle not in use and the connection 230V is not present, disconnect the battery service with the battery
main switch.
CONTROL PANEL NE333
the vehicle engine is running and the parallel batteries is active or in the presence
.
Push button with warning light for turning
PUMP on or off
Push button with warning light for turning
AUX on or off
.
.
symbol remains litm, the alarms are not signaled but the
4
" ) or enable (display shows "
" ) or enable (display shows "
" ) or enable (display shows "
and the night function
GB
")
the
") the
")
the
