Idiomas disponibles
  • ES

Idiomas disponibles

Enlaces rápidos

1. Introduction & Features
Thank you for buying the VDLPROM3! Please read the manual thoroughly before bringing this device into service. Make
sure that the device was not damaged in transit. If the device is damaged, you should contact your dealer and postpone
installation of this device. Verify if the set is complete: a colour mirror ball with attachment ring, a chain with key ring, a
battery operated mirror ball motor, a PAR-36 pin spot with mounting bracket and a PAR-36 lamp.
2. Safety Instructions
Be very careful during the installation: touching live wires can cause life-threatening electroshocks.
Do not touch the device during operation as the housing heats up.
Keep this device away from rain and moisture.
Unplug the mains lead before opening the housing.
• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer
will not accept responsibility for any ensuing defects or problems.
• A qualified technician should install and service this device.
• Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device
against damage by leaving it switched off until it has reached room temperature.
• This device falls under protection class I. It is therefore essential that the device be earthed. The power plug must
only be plugged into a protection class I outlet. Have a qualified person carry out the electric connection.
• Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.
• Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if necessary.
• Disconnect the device from the mains to clean it or when it is not in use. Handle the power cord by the plug only.
• There may be some smoke or a particular smell when the device is activated for the first time. This is normal and
any smoke or smell will gradually disappear.
• Do not look directly at the light source as sensitive people may go into epileptic seizure if they do.
• Note that damage caused by user modifications to the device are not covered by the warranty.
• Keep the device away from children and unauthorised users.
3. General Guidelines
• This set includes a mirror ball and pin spot for use at home, on stages, in discotheques, in theatres etc.
• The VDLPROM3 should only be used indoors with an alternating current of max. 230V AC/50Hz.
• Lighting effects are not designed for permanent operation: regular operation breaks will prolong their lives.
• Do not shake the device. Avoid brute force when installing or operating the device.
• Select a location where the device is protected against extreme heat (see "7. Technical Specifications", p.3), dust
and moisture. Respect a minimum distance of 0.5m between the device's light output and any illuminated surface.
• Use an appropriate safety cable to fix the device (e.g. VDLSC7 or VDLSC8).
• Familiarise yourself with the functions of the device before actually using it. Do not allow operation by unqualified
people. Any damage that may occur will most probably be due to unprofessional use of the device.
• Use the original packaging if the device is to be transported.
• All modifications of the device are forbidden for safety reasons.
• Only use the device for its intended purpose. All other uses may lead to short circuits, burns, electroshocks, lamp
explosion, crash, etc. Using the device in an unauthorised way will void the warranty.
VDLPROM3
VDLPROM3 – DISCO LIGHT SET
1
VELLEMAN
Tabla de contenido
loading

Resumen de contenidos para Velleman HQ-Power VDLPROM3

  • Página 10: Vdlprom3 - Juego De Iluminación Disco

    • Seleccione un lugar de montaje donde el aparato no está expuesto a polvo, humedad y calor extremo. Respete una distancia de mín. 50cm entre la salida de luz y el área iluminado. • Fije el aparato mediante un cable de seguridad (p.ej. VDLSC7 o VDLSC8). VDLPROM3 VELLEMAN...
  • Página 11: Instalación

    • Instale el aparato fuera del alcance de personas no autorizadas y en un lugar con poca gente. • La instalación de este aparato exige una sólida experiencia práctica : debe poder calcular la carga máx. del soporte, debe conocer los materiales necesarios para la instalación, etc. De vez en cuando, una verificación de la VDLPROM3 VELLEMAN...
  • Página 12: Limpieza Y Mantenimiento

    Motor para la bola de espejos Alimentación pila tipo D de 1.5V Velocidad de rotación 1.5 RPM Diámetro máx. de la bola de espejos 20cm (8") Se pueden modificar las especificaciones y el contenido de este manual sin previo aviso. VDLPROM3 VELLEMAN...

Tabla de contenido