Commercial Electric 565682111 Manual De Uso Y Cuidad

Item # 1009385335/ 1009582786/ 1009582785
Model # 565682111/ 565682121/ 565682131
UsE ANd CARE GUIdE
7.5 IN. CONTEMpORARy LOW pROfILE fLUshMOUNT
WITh NIGhTLIGhT
Package contents
Part Description Quantity
A Fixture Body 1
HarDware IncluDeD
Part Description Quantity
AA
AA Mounting Bracket 1
BB Mounting Screw (for Electrical Box) 2
CC Wire Connector 2
DD Trim Ring 1
NOTE: Keep your receipt and these instructions for proof of purchase.
WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the
fuse or turn off the circuit breaker before removing an existing light fixture or installing the new one.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
CHANGING COLOR TRIM RING
This flushmount allows you to customize the color of the trim ring.
NOTE: The product is shipped with the white trim ring installed on the flushmount.
REMOVE THE TRIM RING LOCK THE TRIM RING
Using a pry tool or your fingernail remove the original outer Carefully align the side slots in the desired trim ring (DD) and
ring counterclockwise from fixture base. fixture body (A), then press the fixture body (A) to lock inside
the trim ring (DD).
Side slots a
b
d
c
Side slots
A
Original
outer ring
aDjustIng tHe color temPerature of tHe lIgHt
This LED light fixture allows you to customize the color temperature of the light using
three settings: Soft White, Bright White, or Daylight.
1. Choose your favorite correlated color temperature (CCT) from three options: 3000k Soft
White, 4000k Bright White, or 5000k Daylight.
2. Move the toggle switch on the fixture body (A) to make your selection before inserting into
bracket or ceiling.
NOTE: The factory setting for the correlated color
temperature (CCT) is 3000K Soft White
InstallatIon
1. Pass the hot and neutral (black and white) wires from the electrical outlet box through the middle hole of the mounting
bracket (AA).
Align the mounting bracket (AA) using the mounting screws (BB) and tighten securely to the electrical box.
2. Connect the hot and neutral (black and white) wires from the fixture body (A) to the same color wires from the electrical box.
Cover the wire connectors (CC)
3. Position the wires back inside the electrical box.
Align the side slots on the fixture body (A) with the mounting bracket (AA) and fix the fixture body (A) securely by carefully
rotating in clockwise the side slots inside the mounting bracket (AA).
4. Restore power at the electrical panel. Turn on the light switch to activate the fixture.
A
steP 1.
AA
BB CC
BB
DD
2.75"
3.54"
lIgHt DIstrIbutIon
-/+180
-150
-120
0
-90
70
140
A -60 210
280
-30
350
0
AVERAGE BEAM ANGLE(50%):111.0 DEG
selectIng maIn lIgHt or nIgHtlIgHt moDe
The product can be used in one of two modes: Main light mode, which provides full brightness and allows selection from three
color temperatures, or nightlight mode.
Nighlight mode provides reduced light output at 2000K color temperature for very soft illumination at night.
DD
TO TURN ON THE MAIN LIGHT
1. Turn on the light switch to activate the light fixture.
TO CHANGE TO NIGHTLIGHT MODE
1. Switch the main light off and back on again in 3 seconds to active nightlight mode.
NOTE: The main light will not provide light output when the nightlight trim is illuminated.
5000K 4000K 3000K
TO RETURN TO THE MAIN LIGHT
Switch for color choice
1. Toggle the switch off and back on to active.
care anD cleanIng
CAUTION: Before attempting to clean the tube and luminaire/light fixture, disconnect the power to the fixture by turning
the breaker off or removing the fuse from the fuse box. Clean with a soft, dry cloth. Do not use cleaners with chemicals,
solvents, or harsh abrasives. Do not use liquid cleaner on the LEDs, LED driver, or wiring.
steP 2. steP 3.
AA
CC
A
150
120
90
60
UNIT:cd
C0/180,111.3
C30/210,111.1
30
C60/240,110.8
C90/270,110.8
troublesHootIng
Minor problems often can be fixed without the help of an electrician.
WARNING: Before doing any work on the fixture, disconnect power to the light fixture.
Problem Possible cause
The fixture will not illuminate. The power is off.
The circuit breaker is off.
There is a bad connection.
There is a defective switch.
The fuse blows or the circuit The wires are crossed or the power
breaker trips when the light is wire is grounding out.
turned on.
The light fixture flickers or The dimmer circuit is not compatible
Side slot
makes a buzzing sound. with the product.
The dimming circuit is set outside the
dimming range of the product.
Out of sync Slide the dimmer too fast.
The dimmer circuit is not compatible
with the product.
WARNING: Carefully read and understand the information given in this manual before beginning the assembly and
installation. Failure to do so could lead to electric shock, fire, or other injuries which could be hazardous or even fatal.
• Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
• This product must be installed in accordance with the applicable installation codes by a person familiar with the construction
and operation of the product and the hazards involved. • Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures: Reorient or relocate the receiving antenna, increase the separation between the equipment and
the receiver, connect the equipment into an outlet on a circuit different from that to which the receiver is connected, and consult
the dealer or an experienced radio/TV. Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
warrantY
wHat Is coVereD
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of five (5)
years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal
use and service. If this product is found to be defective, the manufacturer's only obligation, and your exclusive remedy, is the
repair or replacement of the product at the manufacturer's discretion, provided that the product has not been damaged through
misuse, abuse, accident, modifications, alterations, neglect, or mishandling.
wHat Is not coVereD
This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in anyway not in
accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result
of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or
workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as
this is considered normal wear and tear.
The manufacturer does not warrant and specifically disclaims any warranty, whether express or implied, of fitness for a
particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not
be liable for any consequential or incidental loss or damage, including but not limited to any labor / expense costs involved in the
replacement or repair of said product.
Contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.com.
Questions, problems, missing parts? Before returning to the store,
call Commercial Electric Customer Service 8 a.m. - 7 p.m.,
EST, Monday - Friday 9 a.m. - 6 p.m., EST, Saturday
1-877-527-0313 | HomeDePot.com
Retain this manual for future use.
solution
Ensure the power supply is on.
Ensure the circuit breaker is in the on position.
Check to ensure proper wire connections are made.
Contact a qualified electrician.
Contact a qualified electrician.
Check the wire connections.
Contact a qualified electrician or call customer service
1-877-527-0313.
Check the product page at www.HomeDepot.com for a
list of compatible dimmers.
Turn or slide the dimmer switch to adjust the light
output until the flickering or buzzing stops.
Turn off the wall switch for more than 3 seconds, then
turn back on.
Check the product page at www.HomeDepot.com for a
list of compatible dimmers.