Idiomas disponibles
Idiomas disponibles
2.
Push button on selector nozzle, nozzle diat will pop up.
3.
Turn dial until desired spray pattern lines up with
button on selector nozzle.
4.
Push dial in until it locks into place.
Usage Tips
• For most effective cleaning, keep selector nozzle
from 8 to 24 inches (20 to 61 cm) away from
cleaning surface.
If you get selector nozzle too close, especially
using a high pressure spray pattern, you may
damage surface being cleaned.
Do Not get closer than 6 inches (15 cm) when
cleaning tires.
Cleaning
and Applying
Detergent
To apply detergent,
follow these steps:
WARNING
Chemical Burn Hazard.
Chemicals could cause burns resulting in
death or serious injury.
, DO NOT use caustic liquid with pressure washer.
, Use ONLY pressure washer safe detergents/soaps.
Follow all manufacturers instructions.
To apply undiluted detergent using the blue Perfect Mix
siphon, follow these steps:
1.
Review use of selector nozzle.
2.
Attach Perfect Mix siphon hose to pump and
Perfect Mix concentrate bottle
NOTICE
Use standard detergent siphon hose &
filter kit, available at Sears retail item 75180, to apply
standard detergents. Detergent siphon hose & filter kit
is available as an optional accessory. It is not included
with the pressure washer.
NOTICE
Contact
with the hot muffler could damage
detergent
siphoning
tube.
o When inserting the siphon into a detergent solution bottle,
route the tube so as to keep it from inadvertently contacting
the hot muffler.
3.
Make sure SOAP spray pattern nozzle is selected
on selector nozzle.
NOTICE
Detergent cannot be applied with the MAX,
GENERAL, DEUCATE or FLUSH spray pattern nozzles.
4.
Make sure garden hose is connected to water inlet.
Check that high pressure hose is connected to
spray gun and pump. Turn on water.
NOTICE
You must attach all hoses before you start
the engine.
Starting the engine without all the hoses connected and
without the water turned ON could damage the pump.
, Damage to equipment resulting from failure to follow this
instruction will void warranty.
.
6.
.
Start engine following instructions How to Start
Your Pressure Washer.
Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward,
using long, even, overlapping strokes.
Allow detergent to "soak in" for 3-5 minutes before
washing and rinsing. Reapply as needed to prevent
surface from drying. DO NOT allow detergent to
dry on (prevents streaking).
Pressure
Washer
Rinsing
For Rinsing:
.
.
Select and change to desired spray pattern nozzle
on selector nozzle. See How To Use Selector
Nozzle.
Keep the spray gun a safe distance from the area
you plan to spray.
WARNING
Kickback
from spray gun could
cause you to fall resulting
in death or
serious
injury.
Operate pressure washer from a stable surface.
• Be extremely careful if you must use the pressure washer
from a ladder, scaffolding, or any other similar location.
Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.
3.
Apply a high pressure spray to a small area, then
check the surface for damage. If no damage is
found, it is okay to continue cleaning.
4.
Start at the top of the area to be rinsed, working
down with same overlapping strokes as you used
for washing and applying detergent.
Automatic
Cool Down System
(Thermal
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the
spray gun, circulating water in the pump can reach
temperatures above 125°F. The system engages to
cool the pump by discharging
the warm water onto
the ground.
15
