Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Operating instructions
Remote Handset
a = On / Off slide switch
❙
On (green LED illuminates)
£
Off (green LED goes off)
b = Caravan forwards
(both wheels rotate in
forwards direction)
c = Caravan reverse
(both wheels rotate in
reverse direction)
d = Caravan right forwards
(left wheel rotates in
forwards direction)
e = Caravan left forwards
(right wheel rotates in
forwards direction)
f = Caravan right reverse
(left wheel rotates in reverse direction)
g = Caravan left reverse
(right wheel rotates in reverse direction)
The caravan can be turned in a circle on the spot without
moving forward:
d + g = Turn caravan to the right
(left wheel rotates forwards + right wheel rotates
backwards)
e + f = Turn caravan to the left
(left wheel rotates backwards + right wheel rotates
forwards)
The remote hand set automatically switches itself off after ap-
prox. 2 minutes if no button is pressed, or after 7 minutes if one
of the movement buttons is permanently held down. The green
LED goes off.
To reactivate the remote control, move slide switch to "Off"
and then back to "On"
❙
after approximately 1 second.
There is no "On / Off" switch on the caravan to be operated.
Remote hand set LED flash codes and
acoustic signal
LED "On" and no acoustic signal
System is ready for operation
LED "Off" and no acoustic signal
System off
(check remote hand set batteries if necessary)
LED "flashes" in combination with acoustic signal:
–
for approx. 5 seconds after switching the remote hand set
on, until the system is ready for operation.
–
for approx. 10 seconds after switching the remote hand set
on, then it is switched off again – unable to establish radio
link to controller.
–
every 3 seconds if the caravan battery has a low charge
(finish manoeuvring as quickly as possible and charge
battery).
–
5 times a second (5 Hz) if the caravan battery voltage is low.
No manoeuvring is possible until the battery voltage is above
11 V again (e.g. by means of recovery / battery charging).
12
Maneuvering assistant RH1
–
approx. 2 times per second with overcurrent / overtempera-
ture (2 Hz). Switch remote hand set off and on again (wait for
cooling down if necessary in the event of overtemperature).
Changing the batteries in the remote handset
Please be sure to use leak proof micro -
batteries only, type LR 03, AAA, AM 4,
MN 2400 (1.5 V).
When fitting new batteries ensure the
polarity is correct!
Dead and used batteries may leak
and damage the remote handset!
Remove the batteries if the handset is not
going to be used for an extended period.
No claims under guarantee will be considered for damage
caused by leaking batteries.
Before throwing away a defective handset, it is essential that
the batteries are removed and disposed of in proper manner.
Manoeuvring the Caravan
Please read the "Safety instructions" before using
the maneuvering assistant!
With the caravan uncoupled (apply handbrake), engage the
drive rollers to the tyres using the provided lever. Swivel the le-
ver until it cannot be swivelled any further without using exces-
sive force. The drive unit securely engages in the end position.
When engaging or disengaging, ensure your fingers are
not crushed.
Before operating the maneuvering assistant, release the
handbrake.
£
Move slide switch (a) on remote hand set to the "On"
– green LED flashes for 5 seconds in combination with the
acoustic alarm until the control unit is ready for operation.
The six direction buttons provide movement in six directions –
forward, reverse, left forward, left reverse, right forward, right
reverse.
The "left forward" (e) and "right reverse" (f) or "right forward" (d)
and "left reverse" (g) buttons can also be pressed simultane-
ously in order to turn the caravan in a circle on the spot without
moving it forwards.
The soft start / stop facility means that the caravan starts
without jerking and is gently braked when stopping.
If the buttons are released or the radio signal is interfered with
or becomes too weak, the caravan stops. Your maneuvering
assistant cannot be activated by radio devices or other maneu-
vering assistant remote hand sets.
After starting up, the maneuvering assistant moves at a uni-
form speed. The speed will increase a little when going down-
hill and decrease a little when going uphill.
Move slide switch on remote control to the "Off" o position to
switch the remote control and the maneuvering assistant off.
The slide switch also acts as an "Emergency stop"
switch.
After manoeuvring, first apply the handbrake and then disen-
gage the drive rollers away from the tyres.
❙
position
Tabla de contenido
