Mox C40 Serie Instrucciones Y Advertencias Para El Instalador página 3

General safety precautions
EN
Failure to respect the information given in this manual may cause personal injury or
damage to the device.
This installation manual is intended for qualified personnel only.
MOX MOTION GATES cannot be held responsible for any damage or injury due to improper use or any use other the intended usage indicated in this manual.
Installation, electrical connections and adjustments must be performed by qualified personnel, in accordance with best practices and in compliance with
applicable regulations.
Read the instructions carefully before installing the product. Bad installation could be dangerous.
Before installing the product, make sure it is in perfect condition: if in doubt, do not use the equipment and contact qualified personnel only.
Do not install the product in explosive areas and atmospheres: the presence of inflammable gas or fumes represents a serious safety hazard.
Before installing the motorisation device, make all the necessary structural modifications to create safety clearance and to guard or isolate all the crushing,
shearing, trapping and general hazardous areas.
Make sure the existing structure is up to standard in terms of strength and stability.
MOX MOTION GATES is not responsible for failure to observe Good Working Methods when building the frames to be motorised, or for any deformation
during use.
The safety devices (photocells, safety edges, emergency stops, etc.) must be installed taking into account: applicable laws and directives, Good Working
Methods, installation premises, system operating logic and the forces developed by the motorised door or gate.
The safety devices must protect against crushing, cutting, trapping and general danger areas of the motorised door or gate.
MOX MOTION GATES declines all responsibility if component parts not compatible with safe and correct operation are fitted.
Display the signs required by law to identify hazardous areas.
Each installation must bear a visible indication of the data identifying the motorised door or gate.
An omnipolar disconnection switch with a contact opening distance of at least 3mm must be fitted on the mains supply.
Make sure that upline from the mains power supply there is a residual current circuit breaker that trips at no more than 0.03A and overcurrent cutout
upstream of the electrical system in accordance with best practices and in compliance with applicable regulations.
When requested, connect the automation to an effective earthing system
During installation, maintenance and repair operations, cut off the power supply before opening the cover to access the electrical parts.
The electronic parts must be handled using earthed antistatic conductive arms.
Only use original spare parts for repairing or replacing products.
The installer must supply all information concerning the automatic, manual and emergency operation of the motorised door or gate, and must provide the
user with the operating instructions.
The packaging materials (plastic, polystyrene, etc.) should not be discarded in the environment or left within reach of children, as they are a potential source
of danger.
Dispose of and recycle the packing components in accordance with the standards in force.
These instruction must be kept and forwarded to all possible future user of the system.
Declaration of Conformity
I the undersigned, as acting legal representative of the manufacturer:
Roger Technology - Via Botticelli 8, 31021 Bonisiolo di Mogliano V.to (TV)
hereby DECLARE that the appliance described hereafter:
Description: Automation for sectional overhead doors
Model: C40 series
Is conformant with the legal requisites of the following directives:
• Directive 2006/42/CE;
• Directive 2004/108/CE;
• Directive 1999/5/CE;
• Directive 2011/65/UE;
and that all the standards and/or technical requirements indicated as follows have been applied:
EN 60335-2-95:2004
EN 60335-
1:2012/A11:2014 EN
62233:2008
EN 13241-1:2003/A1:2011
EN 301 489-3 V1.4.1 (2002-08)
EN 301 489-1 V1.9.2 (2011-09)
EN 300 220-1 V2.4.1 (2012-05)
EN 300 220-2 V2.4.1 (2012-05)
EN 62479:2010
Last two figures of year in which marking was applied
Place: Mogliano V.to Date: 01-01-2021
that complies with current safety standards.
CE 21
Signature
3