Idiomas disponibles
Idiomas disponibles
PRODUCT SPECIFICATION
The 2-in-1 Hot Air soldering station is an electrical device designed to solder and unsolder surface mounted devices (SMD) with
hot air, or to solder metal materials with tin-lead solders and unleaded solders for soft soldering. The temperature control and
adjustable airfl ow allow for the soldering of fi ne electrical and electronic elements without risk of overheating. The correct, reliable,
and safe operation of the device depends on its proper use, therefore:
Read the entire manual before the fi rst use of the device, and keep it for future reference.
The supplier shall not be liable for any damage resulting from failure to comply with the safety instructions and recommendations
specifi ed in this instructions manual.
ACCESSORIES
The product accessories are shown in the fi gure (I).
TECHNICAL PARAMETERS
Parameter
Catalogue No.
Rated voltage
Rated frequency
Rated power (hot air blower)
Rated power (soldering iron)
Airfl ow rate
Soldering iron supply voltage
Temperature (hot air blower)
Temperature (soldering iron blower)
Temperature stability (hot air blower)
Temperature stability (soldering iron)
Insulation class
Tip-to-ground resistance
Tip-to-ground voltage
Net weight
SAFETY INSTRUCTIONS
Irresponsible use of the equipment can cause fi re, therefore exercise caution when using the equipment in areas where combustible ma-
terials are present; do not direct a stream of hot air at the same spot or place the soldering iron tip to the same spot for an extended period;
do not use the equipment in an explosive atmosphere; be aware that heat may be transferred to combustible materials out of sight; place
the equipment on its stand after use and leave it to cool down before storage; do not leave the equipment unattended when switched on.
Before starting work, make sure that the housing and the power cord and plug are not damaged. In case of damage, do not proceed with
work.
Children must not use this equipment. Children should not play with the equipment. Children left unattended should not be allowed to
perform the cleaning and maintenance of the equipment. This equipment may not be used by persons with reduced physical or mental
abilities and persons with no experience or knowledge of the equipment, if not supervised or instructed on its safe use so that the risks
associated with it are understood.
The device is not designed to operate in high humidity conditions. The temperature at the place of the device's use must be within the range
of 0
C ÷ +40
C, and the relative humidity must be below 70% without condensation. Do not expose the device to precipitation.
O
O
Before connecting the device to the power supply, make sure that the voltage, frequency, and performance of the supply network corre-
spond to the values shown on the device's rating plate. The plug must fi t into the socket. It is forbidden to modify the plug or socket in any
manner to make them fi t. The device must be connected directly to a single supply network socket. It is forbidden to use extension cords,
adapters, or double sockets. The supply network circuit must be equipped with a 16 A protection. Avoid contact between the power cord and
sharp edges and hot objects and surfaces. During operation, the power cord must always be fully extended, and the position of the power
cord must be set so that it does not become an obstacle during operation. The power cord should not be placed in a manner that would
pose a risk of tripping. The supply socket should be located in a place where it is always possible to remove the device power cord plug
quickly. Always pull the power cord by the plug housing when unplugging it, never by the cord. If the power cord or the plug is damaged,
immediately disconnect it from the supply network and contact an authorised service centre of the manufacturer for replacement. Do not
use the product with a damaged power cord or plug. The power cord or plug cannot be repaired and must be replaced with a new one that
is free of defects if these components are damaged.
WARNING! The metal components of the tool can be hot during and immediately after use. Do not touch them, as it may cause severe
O R I G I N A L
EN
Unit of measurement
[V~]
[Hz]
[W]
[W]
[m/min]
[V DC]
[
O
C]
[
C]
O
[
C]
O
[
C]
O
[Ω]
[mV]
[kg]
I N S T R U C T I O N S
Value
YT-82458
220 – 240
50
750
75
120
24
100 – 480
200 - 480
+/- 2
+/- 1
II
<2
<2
1.88
9
