Idiomas disponibles
Idiomas disponibles
EN
burns. Allow the device components to cool down. Use gloves that protect against high temperatures if you need to move these compo-
nents before they cool down. Make sure that the fl oor near the place of use of the device is not slippery. This will prevent slipping, which can
cause serious injuries. Never block or restrict the fl ow capacity of the air inlet openings. Never point the device at people or animals. Do not
check the blowing temperature by directing the air stream towards any part of the body. Never use the device as a hair dryer. Do not use
the device in the bathroom or near water. Do not touch the nozzle or tip end, as this may cause burns. After use, allow the tool to cool down
before storing it. Do not accelerate the process of self-cooling of the device components in any manner.
DEVICE OPERATION
Installation of accessories
CAUTION! Only install the accessories when the supply voltage is disconnected. Pull the tool power cord plug out of the power
socket!
Before assembly and disassembly of the device, make sure that all components have cooled down.
Before starting the assembly, make sure that all switches on the soldering station are in the OFF position – O.
Connect the plug of the soldering iron's cable to the port marked as LUTOWNICA/SOLDERING IRON on the front of the soldering
station housing. The plug has such a shape that it can be connected in one correct way only. Secure the connection by screwing
a metal plug ring on the thread around the port in the soldering station housing.
Connect the plug of the blower's cable to the port marked as DMUCHAWA/HOT AIR on the front of the soldering station housing.
The plug has such a shape that it can be connected in one correct way only. Secure the connection by screwing a metal plug ring
on the thread around the port in the soldering station housing.
The plug of the soldering iron's cable and of the blower's cable are diff erent from each other to minimise the risk of their incorrect
connecting.
Place the soldering iron in the stand and the blower in the holder with the nozzle pointing upwards (II).
If it is necessary to install an injector on the blower nozzle, slide the injector on the nozzle and tighten the screw (III) to fi x it. Do
not overtighten the screw to avoid damaging any of the components.
Connect the power cord to the port at the back of the housing. The plug has such a shape that it can be connected in one correct way only.
Place the soldering iron stand near the station to ensure free access to the soldering iron and prevent the soldering iron tip from
unintentional coming into contact with any object during operation, storage on the stand, and movement of the soldering iron
during operation. Due to the high temperature of the tip, leave at least 10 cm of free space around the stand. The stand should
be placed on a heat-resistant surface.
Insert a sponge designed to clean the tip during operation into the stand cavity. The sponge should be damp but not wet during
the entire operation period. This will prevent the tip damage.
Position the station at the workplace, e.g., on the table to ensure easy access to the controls and that any object does not cover
the display reading. Place the station in such a position as to ensure free access to the blower. Make sure that the blower nozzle
does not unintentionally come into contact with any other object, during operation, storage on the stand, and when moving the
blower during operation. Due to the high temperature of the nozzle, leave at least 10 cm of free space around the station. The
station should be placed on a heat-resistant surface.
Only after setting up the station and the stand and performing a trial operation can the station be connected to the power supply.
Switching the device on and off
Both the soldering iron and blower have independent switches.
Switch the device on by moving the power switch to the on position – I.
The display will show "---" indicating that the station has entered standby mode.
If it is necessary to switch off the device, move the power switch to the off position – O.
Operating the soldering iron
Place the soldering iron on the stand. Use the switch to turn on the soldering iron. The display will show the previous temperature
setting and the current temperature will be displayed after approx. 1.5 seconds. Depending on the selected mode of operation, the
display will show the following parameters: tip temperature – normal mode, indication on the display does not fl ash; temperature
setting – data input mode, indication on the display fl ashes.
The temperature is set by means of the buttons located under the display and marked with arrows. Pressing the arrow up button
increases the temperature. Pressing the arrow down button decreases the temperature. The set temperature will be shown on
display. Pressing the button once changes the temperature by 1
C. Press and hold the button to change the temperature setting
O
faster.
When the tip is heating up, it is indicated by a signal light, which lights up in the lower right side of the display. When the signal light
goes out, it indicates the end of the heating process. If the signal light fl ashes, it indicates a constant temperature.
O R I G I N A L
I N S T R U C T I O N S
10
