Idiomas disponibles
Idiomas disponibles
NOTE: When pulling the starter rope,
do not use the full extent of the rope.
Do not let starter rope snap back. Hold
handle. Let rope rewind slowly.
• Pull starter rope handle firmly and
quickly with your right hand until the
engine attempts to start, but no more
than 5 pulls. Then, push in choke
knob fully. Resume pulling handle un-
til engine starts.
• Above 40°F, allow engine to run for
approximately 5 seconds. Then
squeeze and release throttle trigger to
allow engine to idte.
• Below 40 °F, allow engine to warm up
for 30 seconds to 1 minute with choke
at partial position. Push choke knob in
to the OFF position; then squeeze and
release throttle trigger to allow engine
to idle.
• To stop engine, move On/Stop switch
to the STOP position.
STARTING A WARM ENGINE
DO NOT use the choke to start a warm
engine or flooding and hard starting
may occur.
• Move On/Stop switch to ON.
• Set fast idle lock.
• Be sure choke is in the OFF position.
• With saw on ground, grip front handle
with left hand and place your right foot
through rear handle.
• Pul! starter rope handle until engine
starts.
• Squeeze and release throttle trigger
to return engine to idle speed.
DIFFICULT
STARTING
OR
STARTING
A FLOODED
ENGINE
The engine may be flooded if it has not
started after 10 pulls. Flooded engines
can be cleared of excess fuel with the
following procedure:
• Engage the fast idle lock.
• Verify that the On/Stop switch is in the
ON position.
• Push choke knob to the OFF position.
• With saw on ground, grip front handle
with left hand and place right foot
through rear handle.
• Pull starter rope handle until engine
starts.
• Starting could require many pulls de-
pending on how badly the unit is
flooded. If engine still fails to start, re-
fer to the TROUBLESHOOTING chart or
call 1-800-235-5878.
OPERATING
TIPS
• Check chain tension before first use
and after 1 minute of operation. See
Chain Tension in the Maintenance
section.
• Cut wood only. Do not cut metal, plas-
tics, masonry, non-wood building ma-
terials, etc.
• Stop the saw if the chain strikes a for-
eign objecL Inspect the saw and re-
pair parts as necessary.
• Keep the chain out of dirt and sand.
Even a small amount of dirt will quick-
ly dull a chain and increase the possi-
bility of kickback.
• Practice cutting a few small logs using
the following steps. This will help you
get the "feel" of using your saw before
you begin a major sawing operation.
• Squeeze the throttle trigger and al-
low the engine to reach full speed
before cutting.
• Begin cutting with the saw frame
against the log.
• Keep the engine at full speed the
entire time you are cuffing.
° Allow the chain to cut for you. Exert
only light downward pressure.
• Release the throttle trigger as soon
as the cut is completed, allowing the
engine to idle. If you run the saw at
full throttle without a cutting load,
unnecessary wear can occur.
° To avoid losing control when cut is
complete, do not put pressure on
saw at end of cut.
• Stop engine before setting saw down.
TREE
FELLING
TECHNIQUES
WARNING:
Check for broken or dead
branches which can fall while cutting
causing serious injury. Do not cut near
buildings or electrical wires if you do not
know the direction of tree fall, nor cut at
night since you will not be able to see
well, nor during bad weather such as
rain, snow, or strong winds, etc.
• Carefully plan your sawing operation
in advance.
• Clear the work area. You need a clear
area all around the tree so you can
have secure footing.
• Study the natural conditions that can
cause the tree to fall in a particular
direction. These conditions include:
• The wind direction and speed.
• The lean of the tree. The lean of a
tree might not be apparent due to
uneven or sloping terrain. Use a
