Idiomas disponibles
Idiomas disponibles
5. INSTALLATION.
Read and follow the Safety Information set out in
•
chapter 2 of this document. Failure to adhere to any of
the indications set out in chapter 2 may cause a serious or very
serious accident for those who are in direct contact with the
unit or who are in the vicinity, as well as faults in the unit and/
or in the loads connected to it.
Check that the information on the name plate is the right infor-
•
mation for the installation.
Once you have unpacked the unit, inspect it and ensure that
•
it is in perfect condition before proceeding. If this is not the
case, please contact your distributor.
Limitations to the connection and use of the unit ac-
•
cording to its morphology and sector or work environ-
ment:
For its connection.
ˆ
In units with a power supply plug and output sockets
–
(with no connection
It can be connected by
nical
training; in general, by anyone who uses house-
hold appliances.
For its use.
ˆ
Unit
with no connection
–
signed for household environments and, to a lesser
extent, for shops, industry and other sectors.
The unit can be used by staff with no specific
technical training
tions in the user manual.
Always bear in mind that the UPS is an electrical gen-
•
erator, which is why the user must take the necessary
precautions to prevent direct or indirect contact.
5.1. STORAGE LOCATION AND
CONDITIONS.
Install the UPS in a protected area that does not have exces-
•
sive humidity but has suitable ventilation.
Place the UPS at a distance of at least 20 cm from other units
•
to prevent interference.
Do not operate the unit where the temperature and humidity
•
exceed the permitted limits (see the technical specifications).
20 cm
26
terminals).
staff with no specific tech-
terminals, generally de-
by simply following the instruc-
20 cm
5.2. CONNECTING THE UNIT TO THE MAINS
FOR THE FIRST TIME OR AFTER IT HAS
BEEN OUT OF USE FOR TWO MONTHS.
Insert the mains plug 1 into an AC socket.
•
In models with an IEC socket, a cable is sup-
plied to power the unit. Insert the end of the
2
connector into the base
and the plug on
the other end into the AC socket.
For the best results, charge the battery for
•
at least 4 hours before using the unit for the
first time or when it has been out of use for
more than two months.
Otherwise, the SPS.ONE may not react in
a satisfactory way if there is an outage during the initial op-
erating hours. Its response capacity during unexpected AC
power supply failures is dependent on the energy accumu-
lated in the battery.
The battery charges by simply connecting the unit to the mains.
•
5.3. CONNECTING THE LOADS.
Connect the loads to the sockets
•
rear of the unit.
Never connect a laser printer or
•
scanner to the UPS. This may
damage the unit and/or consume the en-
ergy stored in the batteries, which is re-
served for other more sensitive and more important types of
loads.
5.4. CONNECTING THE COMMUNICATION
CABLE.
To enable unattended start-up/stop of the UPS and to monitor
•
its status, connect one end of the communication cable to the
connector
4
of the USB HID port of SPS.ONE and the other end
to the communication port of the PC.
With the monitoring software installed in your PC, you can pro-
•
gramme the UPS start-up/stopping time, as well as monitor its
status in real-time. Follow the steps described below before
downloading and installing the monitoring software:
5.5. DOWNLOADING AND INSTALLING THE
SOFTWARE.
To download the free monitoring software, register as a user
•
and then register your unit(s) at the following site:
support.salicru.com
You will find a link to the "ACTIVATION GUIDE" on the registra-
•
tion page. Follow the steps indicated.
3
on the
SALICRU
