Redarc BCDC Dual BCDC1225D Manual De Instalación página 3

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 8
TURN ON/OFF THRESHOLDS
Input Open Circuit Low
voltage conditions**
Input Loaded Low voltage
conditions***
Input Overvoltage
shutdown
Output Undervoltage
shutdown**
** Tested every 100 Seconds. | *** Constantly tested.
MOUNTING THE UNIT
The BCDC can be mounted in the cabin of the vehicle, along a chassis rail or
in the engine bay. Ensure that it does not become covered by a build-up of
mud or debris. If mounting in the engine bay, make sure it is positioned away
from high temperatures for best performance.
The unit will operate optimally below 55°C (130°F) with good airflow. At higher
temperatures the unit will de-rate output current up to 80°C (175°F) at which
point the unit will turn OFF.
Ensure the charger is mounted as close as possible to the battery being
charged (auxiliary battery).
The charger can be mounted in any orientation so long as the front decal is
visible. Use all 4 mounting points to fasten using zinc plated G4.6 M5 Screws.
FUSING
REDARC recommend using MIDI style bolt down fuses as they ensure
a low resistance connection. The REDARC FK40 and FK60 fuse kits are
recommended.
Blade type fuses are not recommended as they can result in a high resistance
connection which causes excess heat and may damage the fuse holder and/
or the wiring.
Self-resetting circuit breakers are not recommended as they may trip
prematurely due to the heat generated by the current flowing through the wires.
CHARGE PROFILE SELECTION
Charge Profile Selection (ORANGE Wire)
The ORANGE wire is used to select the Maximum output voltage. This is
achieved by connecting in the following way:
ƒ To select Profile A leave the ORANGE wire disconnected. This will set the
Maximum voltage to 14.6 V.
ƒ To select Profile B connect the ORANGE wire to Common Ground. This
will set the Maximum voltage to 15.0 V.
ƒ To select Profile C connect the ORANGE wire to the RED wire (Input
source positive). This will set the Maximum voltage to 15.3 V.
ƒ To select the Li Profile connect the ORANGE wire to the GREEN wire (LED
output). This will set the charger to Lithium mode.
CAUTION
Check the manufacturer's data for your battery and ensure that
the Maximum voltage of the profile you select does not exceed the
manufacturer's recommended maximum charging voltage. If the Maximum
voltage is too high for your battery type, select another charging profile.
PROFILE B
Li PROFILE
Optional LED
with resistor
EN English | 3
Input
Input Trigger Settings
Turn ON ABOVE
Turn OFF BELOW
Stop Charging BELOW
Turn OFF instantly BELOW
Turn OFF after 20 s BELOW
Turn ON BELOW
Turn OFF instantly ABOVE
Turn OFF after 20 s ABOVE
PROFILE A
PROFILE C
midi
fuse
Input source
positive
12 V Vehicle Input
Standard
Low Voltage
12.9 V
12.0 V
12.7 V
11.9 V
12.2 V
11.3 V
8.0 V
9.0 V
15.5 V
16.0 V
15.6 V
Shutdown if Output Battery < 0.1 V
Input Trigger Settings (BLUE Wire)
The BLUE wire is used to switch the vehicle input turn ON trigger mode
between:
ƒ Standard trigger (for fixed voltage or temperature compensating
alternators)
ƒ Low Voltage trigger (for variable voltage and Idle Stop vehicles)
STANDARD TRIGGER
Leave and tape over the disconnected
BLUE wire, or connect to Ground.
Input Mode
Blue Wire Connection
Not Connected or
Standard
Ground
"D+" for Idle-Stop
Low Voltage
"Ignition" for others
24 V Vehicle Input
Standard
Low Voltage
25.8 V
24.0 V
25.4 V
23.8 V
24.4 V
22.6 V
8.0 V
9.0 V
32.0 V
32.5 V
32.1 V
A single fuse and holder setup
from the Fuse Kits available from
REDARC. Part number FK40 (40 A)
or FK60 (60 A).
LOW VOLTAGE TRIGGER
Connect the BLUE wire to D+ for Idle-stop
vehicles, or IGN for continuous Idle vehicles.
D+
Vehicle
Ignition
12 V Mode
ON
OFF
ON
above
below
above
12.9 V
12.7 V
25.8 V
12.0 V
11.9 V
24.0 V
Solar
N/A
9.0 V
9.0 V
N/A
9.0 V
N/A
32.0 V
33.0 V
N/A
24 V Mode
OFF
below
25.4 V
23.8 V
loading

Este manual también es adecuado para:

Bcdc dual bcdc1240dBcdc dual bcdc1250d