Idiomas disponibles
Idiomas disponibles
APPLICATIONS
Demolishing concrete, chiseling off concrete, grooving, bar
cutting.
Application examples:
Installation of piping and wiring, sanitary facility installation,
machinery installation, water supply and drainage work,
interior jobs, harbor facilities and other civil engineering
works.
SPECIFICATIONS
Voltage (by areas)
Power Input
Full-load Impact Rate
Weight
(According to EPTA-
Procedure 01/2014)
*
Be sure to check the nameplate on this Demolition
Hammer as it is subject to change by areas.
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action
Mounting air tool shanks and
standard hexagonal shanks tools
Mounting standard hexagonal
shanks and retaining groove shanks
without collars
Switch operation
How to use the demolition hammer *
Replacing carbon brushes
Selecting accessories
* Operate this Demolition Hammer by utilizing its empty
weight. The performance will not be better even if it is
pressed or thrust forcibly against the work surface.
Hold this Demolition Hammer with a force just suffi cient
to counteract the reaction.
GREASE REPLACEMENT
This Demolition Hammer is of full air-tight construction to
protect against dust and to prevent lubricant leakage.
Therefore, this Demolition Hammer can be used without
lubrication for long periods. Replace the grease as
described below.
Grease Replacement Period
After purchase, replace grease after every 6 months
of usage. Ask for grease replacement at the nearest
authorized Service Center.
(110V, 220V, 230V, 240V)
1240 W*
1400 min
-1
20.7 kg
Figure
Page
2, 3
2
4, 5
2
6
3
7
3
8, 9
3
―
4
MAINTENANCE AND INSPECTION
CAUTION
Be sure to switch OFF and disconnect the attachment
plug from the receptacle to avoid a serious accident.
1. Inspecting accessories
Since use of a dull accessory, such as a bull point, a
cutter, etc. will degrade effi ciency and cause possible
motor malfunction, sharpen or replace with a new one
as soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws
be loose, retighten them immediately. Failure to do so
could result in serious hazard.
3. Inspecting the retainer
The retainer may become loose due to excessive use.
Always, pay attention to its proper functioning to securely
hold the accessory shank portion. If any wear and tear
is found, bring this Demolition Hammer to an authorized
service center for maintenance service.
4. Maintenance of the motor
The motor unit winding is the very "heart" of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
5. Inspecting the carbon brushes (Fig. 8)
The Motor employs carbon brushes which are
consumable parts. When they become worn to or near
the "wear limit" ⓐ, it results in motor trouble.
When an auto-stop carbon brush is equipped, the motor
will stop automatically. At that time, replace both carbon
brushes with new ones which have the same carbon
brush Numbers ⓑ shown in the Fig. 8. In addition,
always keep carbon brushes clean and ensure that they
slide freely within the brush holders.
6. Replacing carbon brushes
Loosen the screws (Hexagon socket hd. bolt M4×12)
of the cap covers, then remove the cap covers (Fig. 9).
After removing the brush caps, the carbon brushes can
be removed.
After replacing the carbon brushes, tighten the brush
caps, then mount the cap covers securely.
7. Replacing supply cord
If the replacement of the supply cord is necessary, it has
to be done by HiKOKI Authorized Service Center to avoid
a safety hazard.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with
statutory/country specifi c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling instruction,
to a HiKOKI Authorized Service Center.
English
7
