Craftsman 315.115960 Manual Del Operador página 7

A
WARNING: Do not allow familiarity with products to
make you careless. Remember that a careless
fraction of a second is sufficient to inflict serious
injury.
A
WARNING: Always wear eye protection marked to
comply with ANSI Z87.1. Failure to do so could result
in objects being thrown into your eyes resulting in
possible serious injury.
A
WARNING: Do not use any attachments or
accessories not recommended by the manufacturer
of this product. The use of attachments or
accessories not recommended can result in serious
personal injury.
APPLICATIONS
You may use this product for the purposes listed below:
[] Sealing cracks to keep your home's conditioned
air inside while keeping unconditioned air outside,
increasing your home's energy efficiency
[] Filling holes and cracks before painting
[] Creating a moisture barrier around areas that could be
damaged by water
[] Sealing cracks to keep insects from crawling inside
your home
[] Applying adhesive
This product will accept DieHardo 19.2 V lithium-ion
battery packs and Craftsman 19.2 V nickel-cadmium
battery packs.
For complete charging and battery instructions, refer to
the Operator's Manual for the battery packs and chargers
listed in the General Safety Rules.
BATTERY PROTECTION FEATURES
DieHard_e 19.2 V lithium-ion battery packs are designed
with features that protect the lithium-ion cells and
maximize battery life.
If the tool stops during use, release the trigger to reset
and resume operation. If the tool still does not work, the
battery needs to be recharged.
TO INSTALL BATTERY PACK
See Figure 2,
[] Lock the switch trigger by sliding the switch lock up.
[] Place the battery pack on the tool.
[] Make sure the latches on each side of the battery
pack snap into place and the battery pack is secured
on the tool before beginning operation.
CAUTION: When placing battery pack in the
tool, be sure raised rib on battery pack aligns with
the bottom of the caulk gun and latches into place
properly. Improper installation of the battery pack can
cause damage to internal components.
TO REMOVE BATTERY PACK
See Figure 2.
[] Lock the switch trigger by sliding the switch lock up.
[] Depress the latches on the side of battery pack.
[] Remove the battery pack from the tool.
A
WARNING: Battery products are always in
operating condition. Therefore, the switch should
always be locked when not in use or carrying at your
side.
STARTING/STOPPING THE CAULK GUN
See Figure 3.
Before attempting to start the caulk gun, be sure the
switch lock is in the unlocked position.
[] To turn the caulk gun ON, depress the switch trigger.
[] To turn the caulk gun OFF, release the switch trigger.
LOCKING THE SWITCH TRIGGER
See Figure 3.
The switch trigger of the caulk gun can be locked off
using the slide switch located below the switch trigger.
[] To lock the switch trigger, slide the switch lock up.
This will prevent the caulk gun switch trigger from
being depressed.
[] To unlock the switch trigger, slide the switch down.
This will allow the caulk gun switch trigger to be
depressed.
LOADING CAULK
See Figures 4 - 5.
[] Lock the switch trigger by sliding the switch lock up.
[] Using a utility knife, cut off the tip of the spout on
a standard 10 oz. tube of caulk. Cut the tip at a
45 ° angle. Remove as little as possible, taking into
consideration the size of the "bead" of caulk you need.
[] Check for a second inner seal at the base of the spout.
If found, insert the puncture tool inside the spout to
break the seal before using. If using a partially filled
tube, use the puncture tool to remove any hardened
material from the tip.
NOTE: An inner seal is usually found only in
cardboard caulk tubes.
[]
While holding the caulk gun steady with one hand, pull
the handle of the plunger rod away from the caulk gun.
Continue pulling until plunger base reaches the back
of the carriage frame.
7 - English