cecotec READY WARM 800 THERMAL Manual De Instrucciones página 26

ENGLISH
the one next to the device and not the real room one, when setting the temperature, select a
few more degrees than desired ones.
Switching on the electric radiator
1. Connect the device to a power supply and turn the power switch on.
2. The control panel will flash and the "ºC" symbol, room temperature, and power indicator (
) will light up. If the latter does not light up, press the on/off button.
3. Select the desired operating mode by pressing the corresponding button: Day (13) ,Sleep
(14), or Anti-frost (15). The display will show the selected mode.
4. Use the Increase and Decrease buttons to set the desired temperature for the selected
mode. While the temperature is being set, the "ºC" icon will blink.
5. Once the desired temperature has been set, the display will show the room temperature
again.
6. To change to another mode, repeat the above steps.
7. Use the on/off button to turn the radiator on and off.
Thermostat
- When the device reaches the set temperature, it will automatically switch off and the icon
( ) will turn off.
- When the room temperature falls below the set one, the device will automatically turn
back on and the icon will light up again.
Note
- The power indicator may blink when the device is about to turn on or off.
- The set temperatures will be saved even if the device is disconnected or turned off and on.
Reset
To reset the device while it is connected to the power supply and the power switch is on, make
sure the device is unlocked or unlock it with the remote control and press the Decrease button
for 3 seconds. It can also be switched off and on.
Scheduling mode
3 operating modes:
- Day mode: the temperature can be adjusted from 5 ºC to 35 ºC.
- Sleep mode: The temperature can be adjusted from 5 ºC to 35 ºC.
- Anti-frost mode: the temperature can be adjusted from 5 ºC to 15 ºC.
The temperature set manually will be applied to the modes during programmed operations.
Setting the current time and day:
1. Long press the Programming button until the display shows "00:00".
READY WARM 800/1200/1800/2000/2500 THERMAL
50
2. The hour digits will blink. Use the Increase and Decrease buttons to set the current hour
and press the Programming button to save the settings.
3. The minutes digits will blink. Use the Increase and Decrease buttons to set the current
time and press the Programming button to save the settings.
4. The display will show the weekly calendar (Monday corresponds to 1 and Sunday to
7). Select the current day by pressing the Increase or Decrease buttons. Press the
Programming button again to save the settings.
Setting weekly programming:
1. The display will show the first 2 bars for the first period of time (00:00 – 1:00 am) blinking.
It will also show 1 as Monday.
2. Press the desired Mode button (Day, Sleep, or Anti-frost) for the selected time interval.
- If you select Sleep mode, the display will show the Sleep mode icon and the bar on the top
part will blink.
- If you select anti-frost mode, the display will show the anti-frost mode icon and the bar at
the bottom will flash.
- If you select Day mode, the display will show the Day mode icon and the bar at the bottom
and top will flash.
3. When you have selected the desired mode in the first period, press the increase button
and the bars of the second period will flash.
4. Repeat these steps to set the remaining hours.
5. When all the hours in a day have been scheduled, press the Programming button to end
the selected day scheduling and repeat the steps to schedule the 7 days of the week.
6. Once the whole week has been scheduled, press the Programming button and the device
will automatically save the settings and operate in the set mode.
Warning:
When the device is unplugged from the mains, the programming settings will be saved, but you
will have to reset the current time and day of the week.
Resetting the current time and day:
- Perform the same steps as described in the section "Setting the current time and day".
- The display will show the week calendar (Monday-Sunday, 1-7). Use the Increase and
Decrease buttons and operate the On/Off button twice. Then, press the Programming
button and the Increase or Decrease button.
Adjusting temperature under programmed mode:
- During operation, press the On/Off button on the remote control twice and use the Increase
and Decrease button to select the desired temperature.
- Once you have set the temperature, it will be saved for future use in the mode that was
selected, even when used manually.
READY WARM 800/1200/1800/2000/2500 THERMAL
ENGLISH
51