camry CR 4108 Manual De Uso página 4

the products through the feed (1.2).
20. If the appliance is not used or you want to clean it, always disconnect it from the mains
and disconnect the feeder cable from the juice extractor.
21. Do not dismantle the appliance if it is connected to a power socket.
22. Do not use abrasive cleaning sponges or caustic cleaning agents for cleaning the
appliance.
23. The appliance may not be operated for more than 20 minutes without a break.
24. Do not put any hard material, large seeds, ice or frozen products into the feed hole of
the juice extractor.
25. lt is recommended to dismantle the juice extractor and thoroughly wash parts (1.1) to
(1.6) immediately after use.
DEVICE DESCRIPTION (Figure 1)
1. Pusher 2. Feed
3. Worm 4. Mesh filter
5. Rotary drivers 6. Bowl
7. Body 8. Pulp container
9. Juice container 10. Cleaning brush
ASSEMBLING THE APPLIANCE
1. Wash those parts of the appliance that are going to have a direct contact with the fruit and juice.
2 ace the worm (1.3) inside the mesh filter (1.4). Rotate the worm, pressing it slightly down the mesh filter.
he worm will fit into its place. Then, place them in part (1.5). Make sure that the rubber drivers are properly secured in place.
3. Place the 3 joined above-mentioned parts in the bowl (1.6). Rotate parts (1.3), (1.4) and (1.5), pressing them slightly down to make
them fit in the right place.
4. Place the parts assembled in this way in the base of the appliance (1.7), in accordance with Figure 2.
5
U
1
TUU
Place the feed (1.2) on the top and attach it to the juice extractor by turning it clockwise (Figure 4).
Place the pulp and juice containers under the holes (Figure 5).
. Place the juice extractor on a smooth, flat and stable surface. Make sure that the appliance is turned off (the "0" position) before
inserting the plug into the socket.
2. Wash the fruit or vegetables that you want to use. If they do not fit into the feed, (2) cut them into smaller pieces.
3. Start the juice extractor by setting the switch on the cover to "ON".
The juice extractor should not be operated without any products in the feed longer than for 30 seconds.
4. If the juice extractor gets blocked during operation as a result of too much product between the worm and the mesh filter, turn off the
appliance by setting the switch to "0". Then, set the switch to the "R" position to start reverse rotation. If this does not help to unblock
the juice extractor, unplug the device from the power supply, remove parts (1.2) to (1.6) and clean them manually.
5. When you have finished extracting the juice, turn off the appliance by setting the switch to the '0' position and
unplug it from the socket.
ee УИН, AND MAINTENANCE
For easier cleaning, rinse removable parts under running water immediately after every washing. After rinsing, leave the parts to dry.
2 After dismantling, all removable parts can be cleaned in warm water with dishwashing liguid.
3. The stainless steel mesh filter (1.4) must be rinsed in warm water with a little dishwashing liguid not later than 10 minutes after the
end of operation.
4. Do notimmerse the mesh filter (1.4) in bleaching preparations.
5. The mesh filter (1.4) is a part that can be easily damaged. Always handle it carefully.
6. Use the included cleaning brush (1.10) to thoroughly clean the mesh filter (1.4).
7. In the lower part of the bowl there is a rubber plug. It can be gently removed in order to facilitate the washing of the rectangular pulp
outlet. After washing, the rubber plug should be replaced in the bow! outlet.
8. Wipe the body (1.7), which contains the juice extractor motor, with a soft cloth.
9. Juice may cause discolouration of plastic parts. Wash plastic parts immediately after you have used the juice extractor.
10. All metal parts should be thoroughly washed and dried.
NOTE: Never immerse the motor unit in water, nor rinse under the tap. Device is made in class II of insulation
TECHNICAL DATA Device is compliant with EU directives:
Supply voltage: 220-240V = 50Hz - Low voltage directive (LVD)
Maximum power: 150W А | | - Electromagnetic compatibility (EMC)
Maximum operating time: 20-minutes' operation - 60-minutes' break Device marked CE mark on rating label
bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may
A To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste
effect the environment. Do not dispose this appliance in the common waste bin.
4