Idiomas disponibles
Idiomas disponibles
FOR CUSTOMERS IN THE UK
IMPORTANT FOR YOUR SAFETY
The flex supplied with your machine wit have ern two wires or.
three as shown i in the illustrations.
a ae
;
(Earth) .
THREE CORE FLEX
WARNING
.
THIS
APPARATUS
MUST 'BE EARTHED.
IMPORTANT
The wires in this mains lead are coloured in
accordance with the following'code:
Green-and-yellow:
Earth
(")
Blue:
Neutral,
Brown:
Live
As the colours of the wires in the mains lead
of this apparatus
may
not correspond
with
the coloured markings identifying the termi-
nals in your plug, proceed as follows:
é
The wire which is coloured green-and 'yellow
must
be connected.
to the terminai in the.
plug which
is marked by the letter E or by
the safety earth symbol
= or coloured green
or coloured green-and-yellow.
aa
y
j
Z
;
4
Z
The
wire
which
is coloured
blue must
be
Blue
Brown
connected
to the terminal which
is marked
"
with the letter N or coloured black.
(Neutral)
(Live)
The wire which
is coloured brown
must be
connected to the terminal which
is marked
with the letter L or coloured red.
:
TWO
CORE
FLEX
PLUG
IMPORTANT
The wires. in this mains lead are coloured in
accordance with the following code:
Blue: Neutrat,
:
's
(,)
Brown:
Live
As the colours of the wires in the mains lead
of this apparatus
may not.correspond with
|)
the coloured markings identifying the termi-
nals in your plug, proceed as follows:
F
The
wire
whichis
coloured
blue must
be
connected
to the terminal which
is marked
with the letter N or coloured black,
The wire which is coloured brown
must be
connected to thé terminal which is marked
with the letter L or coloured red.
*
Do not connect. any wire to the targer pin
marked E or = when wiring.a plug.
Ensure that all terminals are securely tight-
ened and that no loose strands of wire exist.
Blue
Brown
(Neutral)
(Live)
FOR
CUSTOMERS
IN AUSTRALIA:
If your machine comes with a three core power cord, FOR YOUR SAFETY:
1.
Insert this plug only into an effectively earthed three-pin plug socket
outlet.
2,
If any doubt exists regarding the earthing, consult a qualified electrician.
3.
Extension cords, if used; must be three-core correctly wired,
FOR CUSTOMERS IN THE U.S.A.
SAFETY INSTRUCTIONS
10.
11.
12.
13.
14.
15.
16.
17.
18.
Read Instructions — All the safety and operating instructions should be read befc
the equipment is operated.
Retain Instructions — The safety and operating instructions should be retained f
future reference.
a e
o s
'
Heed Warnings — All warnings on the equipment and in the operating instructio
should be adhered to.
Follov: Instructions
— All instructions for operating and use should be followe
Water and Moisture — The equipment should
not be used near water ~ for examp
near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or neal
swimming pool, etc.
Carts and Stands
— The equipment
should
be used only with a cart or stand that
recommended by Akai.
Wall or Ceiling Mounting
—
Akai does not recommend
mounting the equipment «
a wall or a ceiling.
Ventilation
—
The
equipment-should
be situated
so
that
its location or positic
does not interfere with
its proper ventilation.
For example,
the equipment
shou
not be situated on a bed, sofa, rug, or. similar surface that may biock the ventilatis
openings;
or, placed
in a built-in
installation,
such
as a bookcase
or cabinet
th
may impede the flow of air through the ventilation openings.
Heat
—
The equipment
should
be situated
away
from
heat sources
such
as rad
tors, heat registers, stoves, or other equipments
{including
amplifiers) that produ
heat.
Power
Sources
—
The equipment
should
be connected
to a power
supply
only
the type
described
in the operating
instructions
or as marked
on the equipmer
Grounding or Polarization — The precautions should be taken so that the groundi
or polarization means of an equipment
is not defeated.
Power-Cord
Protection
— Power-supply
cords should be routed so that they aren
likely to be walked
on or pinched by items placed upon or against them, payi
particular attention
to cords at plugs, convenience
receptacles, and the point whe
they exit from the equipment.
Cleaning
— The equipment
should
be cleaned
only as recommended
by the man
facturer.
Power Lines — An outdoor antenna should be located away from power lines.
Outdoor Antenna Grounding — if an outside antenna is connected to the receiv
be sure the antenna system
is grounded so as to provide some protection agair
voltage surges and built up static charges. Section
810 of the National Electric
Code,
ANSI/NFPA
No.
70-1981,
provides
information
with
respect to prop
grounding
of the mast and supporting structure, grounding of the lead-in wire to
antenna discharge unit, size of grounding conductors, location of antenna-dischar
unit, connection
to grounding
electrodes,
and
requirements
for the groundi
electrode. See Figure 1.
Nonuse Periods — The power cord of the equipment should be unplugged from t
outlet when left unused for a long period of time.
Object and Liquid Entry — Care should
be taken so that objects do not fall ai
liquids are not spilled into the enclosure through openings.
Damage Requiring Service — The equipment should be serviced by qualified servi
Personnel when:
A. The power-supply
cord or the plug has been damaged ; or
8. Objects have fallen, or liquid has been spilled into the equipment; or
C. The equipment has been exposed to rain; or
D. The equipment does not appear
to operate
normally
or exhibits
a mark:
change in performance; or
E. The equipment has been dropped, or the enclosure damaged.
Servicing ~ The user should not attempt to service the equipment beyond that a
scribed in the operating instructions. All other servicing should be referred to qua
fied service personnel.
Fig. 1
EXAMPLE OF ANTENNA
GROUNDING
AS
PER NATIONAL
ELECTRICAL CODE INSTRUCTIONS
ANTENNA
LEAD-IN WIRED
GROUND
WIREa.b
TO RECEIVER
ANTENNA
DISCHARGE
UNITS
GROUND
WIRE&@.b
GROUND
CLAMPS
i, GROUNDING
ELECTRODE
t DRIVEN 8' INTO THE
" EARTH
(2.44 METERS)
Use No. 10 AWG (5.3 mm?) copper, No. 8 AWG (8.4 mm?) aluminum, No. 17 AWG
(1.0 mm?)
copper-ciad steel or bronze wire, or larger, as ground wire.
. Secure antenna lead-in and ground wires to house with stand-off insulators spaced
from 4 feet {1.22 m) to 6 feet (1.83 m) apart,
Mount
antenna
discharge
unit
as close as possible
to where
lead-in
enters
house.
