Idiomas disponibles
Idiomas disponibles
ENGLISH
Thank you for buying this product, our company is sure that you will be
more than satisfied with the product's performance. The product is
supplied with a "Warnings" leaflet and an "Instruction booklet".
These should both be read carefully as they provide important
information about safety, installation, operation and maintenance.
This product complies with the recognised technical standards and
safety regulations. We declare that this product is in conformity with
the following European Directives: 89/336/EEC.
1) GENERAL OUTLINE
Movement and presence sensor with active infrared rays for controlling
automatic doors. RIP is a movement and presence detector with active
infrared rays controlled by a microprocessor.
It carries out two functions: it is devised to activate any automatic door
existing on the market, and it is used to detect the presence of anyone
standing in the vicinity of single or double-leaf sliding doors.
•
Four frequencies to be set
•
Self-diagnosis
•
Possible adjustment of the area controlled by the sensor
•
Switch for snow mode preventing any malfunction caused by the
presence of snow, insects etc.
•
Programming of the presence detection time.
2) PARTS IDENTIFICATION (Fig.1)
1) Connector
2) Fitting holes
3) Configuration selectors
4) Sensitivity adjustment
5) Field width adjustment
6) Covering element
Accessories:
7) Drilling template
8) Fitting screws
9) 1.5 m connecting cable
10) Instructions
3) TECHNICAL SPECIFICATIONS
Model
Detection Method
Maximum Installed Height
Pattern Adjustments
Power Supply
Power Consumption
Output Contact
Output Holding Time
Presence Tim er
LED Indication
Temperature Range
Weight
Color
Accessories
4) FITTING INSTRUCTIONS (Fig. 2)
1) Do not install the device over 3 metres in height.
2) Do not leave any moving object within the detection area.
3) Do not install the device in places directly exposed to rain or snow.
4) Do not install the device in places directly exposed to sunlight.
5) Do not install the device in damp or steamy places.
6) Do not install more than four devices near one another, in case of
devices installed near one another, use alternating frequencies as
in Fig. 2.
6 - RIP- Ver. 02
INSTALLATION MANUAL
RIP Motion & Presence Senor
Active Infrared Detection
3m
Pattern Width
Pattern Depth (1 to 4 Rows)
Angle Adjustment 0 t o 5 in 3 steps
Sensitivity
12 to 48 Vac or dc +/-10%
Red & Black wires (Nonpole)
24 Vac-1,3 VA, 12 Vac-1.0 VA
24 Vdc-40 mA, 12 Vdc-80 mA
Form C Relay : DC50V 0.1A (Resistor Load)
Yellow Wire : Normally Open
Green Wire : Normally Close
White Wire : Common
Approx. 0.5 seconds
180, 60, 15 and 2 seconds
RED-Detecting , GREEN-Standby,
ORANGE-Hunting Door,
Switch between RED and GREEN
Abnormal
From –20°C to 60°C
0.190 kg
Silver
Cable : 1.5m, Mounting Template
Installation Instructions
5) FITTING AND WIRING (Fig. 3)
1) Use the drilling template to make the holes for fitting and connection.
2) Remove the cover using a coin or a similar object.
3) Secure the unit using the screws supplied.
4) Connect the cables by pressing together the connectors provided.
5) Position the connector in its seat.
6) Set the sensor parameters as indicates in sections 6 and 8.
7) Position the covering element on the sensor and clean the sensor.
NOTE: To obtain maximum depth and width for the detection
field, fit the RIP device as high as possible and use the maximum
angle available.
6) DIP SWITCH SETTINGS
ON
DEFAULT
SETTING
1
2 3 4 5 6 7 8
Pattern Depth
Presence
(ROWS)
timer
2 sec
4 R
3 R
15 sec
60 sec
2 R
4
3
180 sec
1 R
R
R
1 2
3 4
1) Presence detection timer. The timer can be set using commutators
1 and 2. The RIP device will detect the presence of a fixed object
only for the period of time set in the presence timer. After that the
timer will be reset to zero, and then restarted when any movement
occurs.
2) Detection field depth (lines). Adjust the detection field depth by
setting switches 3 and 4 as shown in the figure.
3) Frequency. When two or more sensors are found within a short
distance, alternating frequencies must be set to prevent any
interference. (H + MH + ML + L = maximum 4 sensors) .
4) Monitoring modes. The snow mode can be selected by means of
the switch. The snow mode must only be used in places subject
to heavy snowfalls or very rigid weather conditions.
5) Self-diagnosis "ON". When supplied with power for the first time,
the RIP sensor automatically starts the self-diagnosis function
(see section 10).
7) POWER
BEFORE APPLYING POWER, READ AND FOLLOW THESE
INSTRUCTIONS.
When power is applied, the sensor will read and store the environmental
optical parameters. This is necessary for Presence Detection to work
properly.
CLEAR THE AREA OF ANY UNNECESSARY OBJECTS.
Apply POWER. Vacate the Detection Pattern immediately. While the
sensor sees ANY moving objects in its DETECTION PATTERN, it will
not proceed to the following step.
DO NOT enter DETECTION PATTERN for 10 seconds (Presence
Detection Setting).TEST the presence feature, especially near the
door.
When carrying out the following work,
TURN OFF THE POWER:
1. in case of any modifications made to the material of the floor (wool
/ rubber)
2. while adjusting the field or detection sensitivity, in order to allow
the sensor to newly detect the environmental optical parameters.
Monitor
Frequency
mode
H
Snow
MH
ML
Normal
2
1
L
R
R
5
7
6
Self
Diagnostic
ON
OFF
8
