Idiomas disponibles
Idiomas disponibles
EN
• The blade bolt and washers were specially designed for your saw. For optimum performance and
safety of operation never use damaged or incorrect bolt/blade washers.
• Check the lower guard for proper closing before each use. Do not operate the saw if the lower
guard does not move freely and close instantly. Never clamp or tie the lower guard into the open
position. If the saw is accidentally dropped, the lower guard may be bent. Raise the lower guard
with the retracting handle and make sure it moves freely and does not touch the blade or any
other part, in all angles and depths of cut.
• Always observe that the lower guard is covering the blade before resting the saw on a surface
after use. An unprotected, coasting blade will cause the saw to move backwards, cutting whatever
is in its path. Be aware of the time it takes for the blade to stop after the trigger switch is released.
• Periodically check that all nuts, bolts and other fixings have not loosened, tighten where
necessary.
The tool must be used only for its prescribed purpose. Any use other than those mentioned
in this manual will be considered a case of misuse. The user, and not the manufacturer,
shall be liable for any damage or injury resulting from such cases of misuse.
The manufacturer shall not be liable for any modifications made to the
tool nor for any damage resulting from such modifications.
Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors.
Kickback Prevention & Operator Safety
Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled
saw to lift up and out of the workpiece toward the operator. Kickback is the result of saw misuse and/
or incorrect operating procedures or conditions and can be avoided by taking precautions as follows:
a) Maintain a firm grip with both hands on the saw and position your arms to resist
kickback forces. Position your body to either side of the blade but not in line
with the blade. Kickback could cause the saw to jump backwards, however, if
precautions are taken, kickback forces can be controlled by the operator.
b) When the blade is binding, or when interrupting a cut for any reason, release the trigger
and hold the saw motionless in the workpiece until the blade comes to a complete stop.
Never attempt to remove the saw from the work or pull the saw backward while the blade is
in motion. Investigate and take corrective action to eliminate the cause of blade binding.
c) When restarting a saw within an incomplete cut, centre the saw blade in the kerf
and check that the saw teeth are not engaged into the material (a binding saw blade
may 'propel upwards' or kickback from the workpiece as the tool is restarted).
d) A large workpiece should be supported close to the line of the cut, and at the edge of the
panel, to prevent sagging. This will minimise the risk of blade pinching and kickback.
e) Do not use dull or damaged blades. Unsharpened or improperly set blades
produce narrow kerf causing excessive friction, blade binding and kickback.
f) Blade depth and bevel adjusting locking levers must be tight and secure before making
a cut. If blade adjustment shifts while cutting, it may cause binding and kickback.
g) Use extra caution when making a 'plunge cut' into existing walls or other
blind areas. The protruding blade may cut objects causing kickback.
h) Check the lower guard before each use and do not use if it does not close freely,
ensuring that the blade does not touch any part of the guard or tool in all angles
and depths of cut. Never clamp or tie the lower guard in the open position.
i) Check the operation of the lower guard spring. If the guard and the spring are not
operating correctly, they must be serviced before use. The lower guard may operate
sluggishly due to damaged parts, gummy deposits, or a build-up of debris.
j) The lower guard should be retracted manually only for special cuts such as
'plunge cuts' and 'compound cuts.' Raise the lower guard by the retracting
handle and as soon as the blade enters the material, the lower guard must be
released. For all other sawing, the lower guard should operate automatically.
k) Ensure that the lower guard is covering the blade before placing the saw down.
An unprotected, coasting blade will cause the saw to 'propel backwards' , cutting
whatever is in its path. Be aware of the time it takes for the blade to stop after the
switch is released. Do not use abrasive wheels, doing so will void the warranty.
l) If a circular saw features a riving knife it must be removed before plunge
cutting. A riving knife will interfere with a plunge cut causing kickback. The
riving knife must always be re-fitted after plunge cutting. A circular saw with a
permanent, non-removable riving knife is NOT suitable for plunge cutting.
12
Product Familiarisation
Front Handle
1.
Spindle Lock
2.
Trigger Lock
3.
Plunge Lock
4.
Trigger Switch
5.
Main Handle
6.
Power Cord
7.
Rear Bevel Lock
8.
Rear Track Fine Adjustment Cam
9.
10. Base Plate
11. Track Sight Panel
12. Front Track Fine Adjustment Cam
13. Front Bevel Lock
14. Bevel Angle Scale
15. Depth Adjustment Screw
16. Motor Cover
17. Depth Scale
18. Blade Housing
19. Width of Cut Indicators
20. Blade Access Window
21. Dust Extraction Port
22. Cut Depth Lock
23. Track
24. Track Assembly Bar
25. Hex Key (x 2)
26. 32mm Vacuum Adaptor
27. Clamp (x 2)
Intended Use
Circular saw for freehand and track-bound operation, performing light to medium-duty plunge cuts
into wooden floorboards, countertops, and similar materials.
Unpacking Your Tool
• Carefully unpack and inspect your tool. Familiarise yourself with all its features and functions.
• Ensure that all parts of the tool are present and in good condition.
• If any parts are missing or damaged, have such parts replaced before attempting to use this tool.
WARNING: Always disconnect from the power supply before carrying out any assembly,
maintenance or cleaning.
