Idiomas disponibles
Idiomas disponibles
GETTING STARTED
ASSEMBLY
Fully assemble product prior to use.
1
Slide the handle into the base until you hear
a "click".
2
Wrap the power cord around the cord hooks for
convenient storage.
3
Position Nozzle onto foot, making sure to
align the tabs at the top of the Nozzle with the
notches inside the foot.
4
Slide Nozzle forward to snap into position.
IMPORTANT:
The Nozzle must be
in the proper position for the cleaner to have
proper suction.
FILL THE CLEAN WATER TANK
WARNING:
To reduce the risk of
personal injury, unplug before cleaning or
servicing.
1
Lift up to remove the Clean Water Tank.
2
Remove the cap and add warm water to the top
of tank. Replace cap.
3
Align Clean Water Tank with the body of the
cleaner and press FIRMLY into place.
FILL THE SOLUTION TANK
1
Remove the Solution Tank from the back of the
cleaner.
2
Remove the cap and fill with HOOVER®
Cleaning Solution to the top of the tank.
Replace cap.
3
Place the Solution Tank back into the cleaner
and press FIRMLY into place.
CAUTION:
Do not clean over floor
electrical outlets. Water will drip from the
brushes and underside of the product after
use and may puddle. To avoid damage to wood
and laminate flooring and to avoid potential
slip hazard, after use (a) do not leave the
product on wood and laminate surfaces and
move to a hard surface and (b) place cleaner
on an absorbent material (such as a towel) to
soak up drips.
BEFORE YOU BEGIN CLEANING:
Vacuum carpet and upholstery thoroughly with
a HOOVER® vacuum before use.
Don't use the carpet cleaner as a traditonal
vacuum cleaner.
Use your HOOVER® carpet cleaner only if
upholstery fabric is marked with a "W" (for
"wet" clean) or "S/W" (for "solvent/dry" or "wet"
clean). Don't clean fabric marked "S" ("solvent/
dry" clean only).
Test for colorfastness in a small, hidden area.
Gently rub surface with a dampened white
cloth. Wait ten minutes and check for color
removal or bleed with a white paper towel.
OPERATIONS
PRETREATING:
For best results, pretreat stains with a HOOVER®
spot treatment to help loosen and remove even
the most stubborn stains.
NOTE:
To avoid damage to wood floors
underneath area rugs or carpet, place
waterproof material (ex: plastic) underneath
them before cleaning.
HOW TO CLEAN CARPETS
1
Unwrap the power cord and plug cleaner in an
electrical outlet.
2
Step on the gray Handle Release Pedal to
recline the cleaner to cleaning position.
3
Step on the red On/Off Pedal to turn ON.
4
Slowly move forward. The cleaner will
automatically dispense the optimal amount of
water and cleaning solution.
5
Slowly pull backward. The cleaner will
automatically dry your carpets by extracting
the water and cleaning solution.
6
For best results, HOOVER® recommends
rinsing the carpet with clean water only. This
will remove residual carpet cleaning solution
from your carpets. To rinse with clean water
only, remove the Solution Tank and then repeat
steps 4 through 5.
7
When you finish cleaning but further drying is
required, press the DRY ONLY BUTTON. The Dry
Only mode will extract remaining water from
your carpet. Continue in this mode until little
water is visibly passing through the Nozzle.
CLEANING FLUID
SEE THE HOOVER'S SOLUTION GUIDE insert or
visit Hoover.com/cleaning-solutions.
MAINTENANCE
This product contains no serviceable parts.
If appliance is not working as it should, has
been dropped, damaged, left outdoors, or
dropped into water, call customer service at
1.800.944.9200 prior to continuing use.
HOW TO EMPTY DIRTY WATER
1
Turn the cleaner off and unplug from electrical
outlet.
2
Grab the Dirty Water Tank handle and pull up
to release. Remove Tank from carpet cleaner
base at an angle.
3
Place on a flat surface and unlatch Dirty Water
Tank lid to remove top of tank.
4
Empty tank, rinse, and allow to air dry.
NOTE:
Keeping the filter clean is critical
to maintain strong suction performance.
AUTO SHUT OFF FLOAT:
Your carpet cleaner is equipped with a shut
off float within your Dirty Water Tank. When
the Dirty Water Tank becomes full, the float
will rise, shutting off the air flow through the
Nozzle. Once the air flow is shut off, empty the
Dirty Water Tank.
IMPORTANT:
Regarding the Dirty
Water Tank: For full suction it is important that
the Dirty Water Tank Lid is securely in place. If
misplaced, poor or no suction will result.
For full suction, it is important that the Dirty Water
Tank is properly secured before cleaning.
