Good Earth Lighting AC1275-RWF-24LFW-G Instrucciones De Instalación

Hardware kit*
Trousse de quincaillerie*
Kit de aditamentos*
Power cord
Cordon d'alimentation
Cable de alimentación
*Actual hardware may differ from illustration/ *La quincaillerie incluse peut être différente de l'illustration./ *Los aditamentos reales pueden diferir de los que se muestran en la ilustración.
DO NOT ATTEMPT TO INSTALL STRIP LIGHT WHILE PLUGGED IN.
WARNING: DO NOT attempt to alter any of the parts of this fixture. All parts are enclosed and not replaceable or serviceable.
WARNING: DO NOT use with extension cords near water or wherever water may accumulate.
WARNING: DO NOT use this product near of highly flammable materials liquids and gases.
WARNING: The wall transformer needs to be mounted 12 inches or more above the ground and should be protected from weather.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
CAUTION: DO NOT power Strip light while packed in plastic spool or while tightly coiled. Excess heat could melt the spool and/or cause damage
to the light.
CAUTION: DO NOT fold or cover light with any material. Repeated bending, sharp edges, twisting and excessive pressure may damage the
product voiding the warranty.
CAUTION: DO NOT Install within 5 feet of a swimming pool, submerge or mount in an area that is prone to standing water.
1. No parts are serviceable on this product. DO NOT alter anything in this
kit. (Kit does not include end caps or glue to seal if cut)
2. DO NOT INSTALL WHILE UNIT IS PLUGGED IN. DO NOT plug the
power cord into the power source until installation is complete.
3. For electrical requirements, see back of driver label.
4. For INDOOR and OUTDOOR wet locations.
5. DO NOT touch, operate, or install fixture while in contact with water. Not
intended for illumination of aquariums.
6. DO NOT mount over sinks or stoves.
7. NOT intended for recessed installation in ceilings or soffits. DO NOT run
ANY cords behind walls, ceilings, soffits, cabinets or a similar permanent
structure where it may be inaccessible for examination.
8. Strip light must be fully uncoiled for proper operation, and to prevent
overheating.
9. This Strip light is NOT expandable. Additional LED Strip light lengths
CANNOT be added.
10.DO NOT look directly at lighted LEDs for any length of time.
This product has a polarized plug (one blade is wider than the other) to reduce the risk of electric shock. The plug only fits one way into a polarized outlet. DO
NOT ALTER THE PLUG. READ THE ENTIRE MANUAL PRIOR TO INSTALLATION. Verify package and hardware contents. Save these instructions.
Select a location for the LED Strip light and mark it. Verify that the power cord reaches the nearest power outlet and will reach the LED Strip light. Thoroughly
clean the mounting surface with rubbing alcohol and allow it to dry. DO NOT PLUG THE POWER CORD INTO THE POWER SOURCE UNTIL
INSTALLATION IS COMPLETE.
CONNECTING CONTROLLER/STRIP LIGHT/ ADAPTER
NOTE: THESE CORDS ARE DESIGNED TO PLUG-IN ONE WAY ONLY.
The plug and cord have two different ends: one input and one output.Line
up the arrow, and Insert the OUTPUT PLUG END into the OUTPUT
CONNECTOR of the preceding fixture and insert the INPUT PLUG END
into the INPUT CONNECTOR of the fixture being added. Twist the water
tight connection piece until completely tightened.
KIT DE RUBAN LUMINEUX WIFI RVNB POUR INTÉRIEUR OU EXTÉRIEUR (Page 3)
KIT DE FRANJA LUMINOSA RVAB WI-FI PARA EXTERIORES/INTERIORES (Página 5)
LED Strip light
Ruban lumineux à DEL
Franja luminosa LED
WIFI enabled RGBW controller
Contrôleur RVNB compatible WIFI
Controlador RVAB habilitado para WIFI
WARNINGS AND CAUTIONS
IMPORTANT SAFETY INFORMATION
INSTALLATION
OUTPUT
PLUG END
INPUT
PLUG END
SAVE AND ATTACH RECEIPT HERE
INDOOR/OUTDOOR RGBW STRIP LIGHT KIT (Page 1)
Model / Modèle / Modelo #: AC1275-RWF-24LFW-G
screws (X40)
des vis (X40)
tornillo (X40)
Mounting Clips (X20)
Clips de montage (X20)
Clips de montaje (X20)
11.Lights may be installed inside of an enclosure, such as a cabinet,
ONLY when thePOWER ADAPTER is located outside of the
enclosure.
12.Use only insulated staples or plastic ties (not included) to secure the
cords.
13.DO NOT use with an extension cord. Use a power strip with integral
over current protection to supply power to the fixture. NEVER use
power strip unless the plug can be fully inserted.
14.DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT. If
dimmer controls are present, remove and replace.
15.If unfamiliar with electrical installations, contact a qualified
electrician to install.
16.LEDs gradually emit less light over their lifetime.
17.ONLY plug into a GFCI certified outlet for outdoor uses.
18.Verify all connections are tightly secured to deter the entry of water.
19.IP65 water and dust resistant on strip light and IR controller. The
driver plug is rated for wet locations.
The two different cords have two different ends: one input and one output. Insert
the OUTPUT PLUG END into the OUTPUT CONNECTOR of the preceding
fixture and insert the INPUT PLUG END into the INPUT CONNECTOR of the
fixture being added. Twist the water tight connection piece until completely
tightened.
Required
Nécessaire
Se necesita
OUTPUT PLUG END
INPUT PLUG END
OUTPUT PLUG END
INPUT PLUG END