Metabo HPT UU 240R Instrucciones De Seguridad E Manual De Instrucciones página 12

Soporte universal de ingletadora
Tabla de contenido
Idiomas disponibles

Idiomas disponibles

English
● The cutting head of all sliding miter saw must be
locked in both the forward and down positions before
any attempt is made to mount to the stand. Failure to
do so may result in serious personal injury.
● Do not use the miter saw on the stand when the legs
of stand are folded.
● Layout the power cable neatly to prevent the power
cable causing the stand to tip over when performing
cutting operations.
8. Unplug the miter saw and lock the cutting head to its
down position. If the miter saw has a sliding rail, lock
the cutting head at down and forward position. Put
the miter saw on the mounting brackets assembly.
NOTE: For your own safety, position the miter saw
on the brackets with the help of two or more people.
9. Slide the square nuts (1) to the slots of the auxiliary
mounting brackets (2) and align to the mounting
holes of the miter saw. (Fig. N)
10. Insert the bolt (7) through the small washer (8),
the mounting hole of the miter saw, the slot of the
auxiliary mounting bracket (2) into the square
nut (1) to mount and lock the miter saw to the
auxiliary mounting bracket. (Fig. N) Repeat the above
steps for the other three mounting holes to lock the
miter saw onto the mounting bracket assembly.
NOTE: Adjust the position of the auxiliary mounting
brackets as close as possible to the front end of the
saw mounting brackets.
11. Tighten all screws (5) and bolts (7) using a 5 mm hex
wrench.
12. After securely mounting the miter saw, unlock the
hold-down latch of the miter saw and carefully
move the cutting head up and down. If the stand tends
to fall down, reposition the miter saw.
13. Unlock the slide carriage lock knob of the miter saw
and carefully slide the cutting head forward. If the
stand tends to fall down, reposition the miter saw for
more stable position on the brackets.
14. Carefully perform sliding movement test at the
maximum miter and bevel angles to ensure the stability
of the stand and the miter saw.
● Do not mount the miter saw with the front of the saw
on the back side of the stand. The miter saw should
be mounted with the wheels of the stand to the right
when facing the front of the miter saw as shown in
Fig. N.
● When you dismount the miter saw, remove the miter
saw together with the mounting brackets assembly,
so that you can put the miter saw and the mounting
brackets assembly all together from next time. For
your own safety, mount or dismount the miter saw by
two or more people.
WARNING
WARNING
Fig. N
7
8
1
Left side
of stand
INSTALLING THE ANCHOR PLATE (FIG. O)
Hardware Bag "P" - Please follow the steps to
assemble the anchor plate to make the stand stable for
operation.
1. Move the stand to a desired place and make sure it
is on a flat surface.
2. Loosen the nut (1) at the inner side of the sleeve (2),
using two 17 mm wrenches.
3. Locate the anchor plate (3) onto the sleeve (2) and
tighten the nut (1) again.
4. Repeat above steps for assembling the other anchor
plate.
5. Fix both anchor plates (3) to the flat surface with
anchors (screw, bolt, peg etc. (not supplied)) which
are suitable for the type of ground surface (soil, wood
flooring, concrete etc.).
● Ensure that both anchor plates are fixed firmly to the
ground and the stand is stable.
● Appropriate way to fix the anchor plates may differ
according to the type of ground surface. If the anchor
plates are not firmly fixed and the stand is unstable,
please take appropriate measures to fix the anchor
plates.
Fig. O
– 12 –
Right side
of stand
2
WARNING
not included
2
1
3
Tabla de contenido
loading

Tabla de contenido