Multiplex FunJet 2 Instrucciones De Montaje página 15

Assembly instructions
12. Installing and fastening the motor
⓫
Place the bulkhead holder
facing downward); if everything fits correctly, glue it onto the fuselage
using Zacki ELAPOR . Fig. 13
®
13. Connecting the motor
Since the motor operates in "pressure mode", it must be operated in
counterclockwise direction.
14. Preparing the power unit
Screw the motor to the bulkhead
entire drive train is inserted into the fuselage from the rear through the
bulkhead.
When assembling the motor, the motor cables are hooked into the cable
㊴
protection . To do so, insert the drive train, twisted approx. 90° to the
left. Turn the motor with the bulkhead to the right and make sure the
motor cables are caught in the cable holder. Fig. 14
Screw the bulkhead to the motor mount using the screws
Connect the controller to the receiver.
The propeller in the FunJet ULTRA works on thrust, therefore it must be
orientated in the driver in such a way that the front side points forward
in the direction of flight. Fasten the propeller properly and check it for
damage and secure fitting prior to each start-up. If in doubt, replace the
propeller. Fig. 15
The propeller must be balanced!
Caution:
Never stand in the direction of flight when the propeller is running.
Warn others of the danger. This is your responsibility!
15. Gluing the vertical tail
Initially apply the decals to the tail units.
8 9
Fit the vertical tails and
flat on the wing, slightly rework if necessary, e.g. by removing burr.
Apply Zacki ELAPOR to the rudder pockets on the wing and insert the
®
rudders. Align and fix immediately before the adhesive has set. Fig. 16
16. Final assembly
For the receiver, glue a strip of hook and loop tape (hook side)
corresponding position in the fuselage. Glue the opposite side (velour) to
the receiver. Install the antennas in the slots provided on the underside
of the wings.
For the drive battery, glue the battery mount plate
but first insert the fastening strap
tape (hook side) to the mount plate Glue one strip of hook and loop tape
(velour) each on the top and bottom of the drive battery.
on the fuselage for test purposes (scale
㉝
and connect the controller. The
㉞
"dry". If the glued sections do not lie
⓴
㊲
into the fuselage,
㊳
. Then glue a strip of hook and loop
Fixing the drive battery:
Initially fix the battery at the correct position on the underside. Hook one
side of the fastening strap on the top of the battery to the velour, tighten
the strap and then clip it on. Fig. 17
The final exact position of the flight battery is specified when determining the
center of gravity.
Check that the battery is fastened securely prior to each start!
For test purposes, connect all the connections.
Do not connect the drive battery until your transmitter is switched
on and you are sure the operating element for the motor control
is set to "OFF".
It is necessary that your controller has a so-called BEC circuit (receiver
power supply from the flight battery). Now switch on the motor briefly and
carefully, and check again the direction of rotation of the propellers (hold
the model during the trial run, remove any loose, light objects located
behind the model).
Caution:
There is a considerable risk of injury due to motors and propellers!
㊱
and .
17. Rudder deflections and settings
To achieve a balanced control, the size of the rudder deflections must be
set correctly.
The elevator upward (joystick pulled back)
and downward (joystick pushed forward)
Set the aileron deflections
(negative differentiation).
If your remote control does not permit these distances, you need to adjust
the pushrod connector.
The neutral position for the first start is approx. 2 mm to "up".
Once you have successfully acquired the basic settings, the
deflections may also be 20% larger.
When flying, you will usually have to trim down. After the first landing,
mark these rudder positions with a waterproof felt-tip pen on the vertical
tails. Prior to each start, trim to "up" approx. 1 mm above this mark.
After climbing, trim down again accordingly. Another tip for perfectionists:
Like all propeller aircraft, the model rotates slightly against the torque of
the motor around the longitudinal axis. In our case, to the left at full throttle.
If the remote control allows it, add a little speed => crosswise. However, this
setting is not a "must".
to the
18. Down thrust presetting
The down thrust can be adjusted at the motor mount. The screws
must be loosened slightly for adjustment. Adjust the down thrust with the
㊱
screw and then tighten the screws
For the initial flight, align the bulkhead, making sure it is parallel to the
trailing edge of the motor mount.
Caution:
Do not over-tighten the screws, otherwise the bulkhead will bend!
10 mm
8 mm.
+/- 8/11 mm
㉞
㉞
again.
15
EN