Parts List - Multiplex RR EasyGlider 26 4205 Manual De Instrucciones

The other important parameter in glider performance is the glide
angle. This is stated as a ratio, i.e. from a particular altitude the
model flies such and such a distance. The glide angle increases
as wing loading rises, and at the same time - of course - the
model's airspeed increases. This becomes necessary if you
wish to fly in relatively strong winds, and when you need "energy
retention" for flying aerobatics.
For thermal flying you need a good glide angle too, as this is the
key to flying across areas of "sink" (the opposite of a thermal)
quickly, so that you can seek out another thermal. To increase
the glide angle you need to increase the wing loading, and this
is done by increasing the glider's weight, i.e. by installing ballast
in the model. This should be positioned in the wing if possible.
In the EasyGlider there is an ideal location: it is the GRP tube
which forms the wing joiner. The internal diameter of this tube is
7.8 mm. Normally a ballast rod of this size would be difficult to
find, and expensive to purchase. However, by chance the diameter
of standard M8 studding (threaded rod) is just the right size. This
material has a diameter of 7.7 mm, and you will be able to buy
it at low cost in any DIY store. You may find that only half a full
length is sufficient. In this case you must ensure that the rod
cannot slide from side to side, e.g. by fitting lengths of balsa
dowel in both ends of the wing joiner, so that the weight is held
in the centre.
Safety
Safety is the First Commandment when flying any model aircraft.
Third party insurance should be considered a basic essential. If
you join a model club suitable cover will usually be available
through the organisation. It is your personal responsibility to
ensure that your insurance is adequate.
Make it your job to keep your models and your radio control
system in perfect order at all times. Check the correct charging
procedure for the batteries used in your RC set. Make use of all
sensible safety measures and precautions which are advised

Parts list

RR EasyGlider
RR EasyGlider Electric
Part No. Description
No. off
1 1 1 Building instructions
2 1 1 Decal sheet
3 1 - Glider fuselage (factory-assembled) with two servos and pre-fitted canopy
5 - 1 Electric fuselage (factory-assembled) with geared motor, speed controller, two servos and pre-fitted canopy
8 1 1 Wing set (factory-assembled) with two servos
12 1 1 Tailplane / elevator with horn and pushrod connector fitted
13 1 1 Fin / rudder with horn and pushrod connector fitted
14 - 1 Pair of propeller blades with screws and sleeves
20 2 2 Hook-and-loop tape, hook
21 2 2 Hook-and-loop tape, loop
29 1 1 Allen key
40 1 1 Wing joiner tube
EasyGlider launch system
50 1 - Handle and Tow Line
51 1 - Pennant (wind direction)
52 1 - Towring
60 1 1 CD: construction video, simulator, product information
Replacement parts (see page 48; please order from your model shop)
16
for your system. An excellent source of practical accessories is
the MULTIPLEX main catalogue, as our products are designed
and manufactured exclusively by practising modellers for other
practising modellers.
Always fly with a responsible attitude. You may think that flying
low over other people's heads is proof of your piloting skill; others
know better. The real expert does not need to prove himself in
such childish ways. Let other pilots know that this is what you
think too. Always fly in such a way that you do not endanger
yourself or others. Bear in mind that even the best RC system in
the world is subject to outside interference. No matter how many
years of accident-free flying you have under your belt, you have
no idea what will happen in the next minute.
The fascination of it all
Model flying is, and always has been, a fascinating hobby, and a
thoroughly enjoyable way of spending your leisure hours. Take
your time to get to know your new EasyGlider / EasyGlider Electric
really well. Plan to spend many hours in the open air, where you
will learn to appreciate the model's excellent performance and
its docile handling. You can join us in enjoying one of the few
types of sport which combine high technology, manual dexterity,
and sophisticated personal skills. You can fly alone or with
friends, and at the same time you can enjoy the pleasures of
nature - treats which have become rare in today's world.
We - the MULTIPLEX team - wish you many hours of pleasure in
building and flying your new model. Happy landings!
MULTIPLEX Modellsport GmbH & Co. KG
Model Development Dept.
Klaus Michler
GB
# 26 4205
# 26 4207
Material
Plastic
Plastic
Metal
GRP tube
Nylon / Inj. moulded plastic
Plastic
Steel
Dimensions
25 x 60 mm
25 x 60 mm
1.5 mm A / F
10 Ø x 8 Ø x 1000 mm
0.5 mm Ø x 75 mm
Ready made
14 mm Ø