Detergent System (Ecoflex™ Only) - Advance CS7000 Serie Instrucciones De Uso

A-18 / ENGLISH
DETERGENT SYSTEM PREPARATION AND USE (ECOFLEX MODELS ONLY)
The Detergent Cartridges (47) are located below the Operator's Seat (2). Fill the detergent cartridge with a maximum of 2.2 gallons (8.32 Liters) of
detergent. SERVICE NOTE: Remove the detergent cartridge from the detergent box prior to fi lling to avoid spilling detergent on the machine.
It is recommended that a separate cartridge be used for each detergent you plan to use. The detergent cartridges have a white decal on them so
you can write the detergent name on each cartridge to avoid mixing them up. When installing a new cartridge, remove the Cap (BC) and place the
cartridge in the detergent box. Install the Dry Break Cap (BD) as shown.
The system should be purged of previous detergent when switching to a different detergent. SERVICE NOTE: Move machine over fl oor drain
before purging because a small amount of detergent will be dispensed in the process.
To Purge When Changing Chemicals (SCRUB AND SOLUTION SYSTEMS MUST BE OFF):
1 Disconnect and remove the detergent cartridge.
2 Turn the key switch (A) to the RUN (ON) position. Wait a few seconds for the start-up sequence to fi nish. 3 Press and hold the Detergent Switch (X) and the Solution Switch (U) for approximately 2 seconds. Release the switch when the chemical
purge icon (C12) appears on the display and the indicator on the detergent switch (X) starts fl ashing. NOTE: Once activated the purge
process takes at least 20 seconds. See illustration on next page for Detergent System indicators. Normally one purge cycle is adequate to
purge the system.
To Purge Weekly (SCRUB AND SOLUTION SYSTEMS MUST BE OFF):
1 Disconnect and remove the detergent cartridge. Install and connect a Cartridge fi lled with clean warm water.
2 Turn the key switch (A) to the RUN (ON) position. Wait a few seconds for the start-up sequence to fi nish.
3 Press and hold the Detergent Switch (X) and the Solution Switch (U) for approximately 2 seconds. Release the switch when the chemical
purge icon (C12) appears on the display and the indicator on the detergent switch (X) starts fl ashing. NOTE: Once activated the purge
process takes at least 20 seconds. See illustration on next page for Detergent System indicators. Normally one purge cycle is adequate to
purge the system.
When the detergent level is nearing the bottom of the cartridge it is time to refi ll or replace the cartridge(s).
SERVICE NOTE: Follow the "To Purge Weekly" instructions above if the machine is going to be stored for an extended period of time or if you
plan to discontinue use of the detergent system.
Detergent Ratio (SCRUB SYSTEM MUST BE ON):
No detergent is dispensed until the scrub and detergent systems are activated and the Drive Pedal (37) pushed forward.

The detergent mixture icon
There are 4 modes of EcoFlex operation:
1. Low Concentration Detergent – The detergent ratio default is 256:1.
2. Maximum concentration detergent – The detergent mixture rate may be adjusted by pressing and holding the detergent switch (X) for
two seconds, (start with the detergent system in the off position). Release the switch once the detergent switch indicator (X1) begins
fl ashing. While the light is fl ashing, pressing and releasing the detergent switch will cycle through the available ratios (300:1, 256:1,
200:1, 150:1, 128:1, 100:1, 64:1, 50:1, 32:1, 26:1). Once the desired ratio is displayed on the screen (C1), stop and it will lock in after
3 seconds. Do not use a concentration level exceeding the detergent manufacturer's recommendation.
3. Burst of Power – Press the Burst of Power Switch (P) to increase the detergent ratio for one minute to the next higher level of
concentration (e.g. 50:1 to 32:1) or the operator pre-programmed concentration ratio (as noted in programming instructions below)
whichever is greater. This will also cause the solution fl ow rate to increase to the next level and the scrub pressure to increase to the
next level. EcoFlex Indicator (P1) will blink for one minute.
4. Plain Water - During scrubbing, the detergent system can be turned off at any time by pressing the Detergent ON/OFF Switch (X) to
allow scrubbing with water only. Detergent Indicator (X1) will be OFF.
Once set, the detergent fl ow rate automatically increases and decreases with the solution fl ow rate, but the detergent ratio remains the same. If an
operator would prefer the fl exibility of setting different detergent concentration ratios and different solution fl ow rates to correspond with each scrub
pressure setting (Normal, Heavy & Extreme) follow the steps below to enter the User Options Menu.
1. Turn the Key Switch (A) to the Off position.
2. Press and hold both One-Touch™ Scrub Switch
until the User Options Menu appears on the LCD Display (C).
3. Use the Scrub Pressure Increase
4. Press the One-Touch™ Scrub switch
5. Press the Scrub Pressure Decrease switch
6. Press the One-Touch™ Scrub switch
Ratio (if installed). Press the One-Touch™ Scrub switch (R) to save each entry. Press the Solution switch (U) to exit any submenu without
saving.
7. There is a similar submenu for both Heavy Scrub and Extreme Scrub which allows customized settings to be saved.
8. Turn the Key Switch (A) to the Off position to exit the hidden menus.
A-18 - FORM NO. 56041979 - CS7000
(C1) will always be displayed when the detergent system is on.
(R) and Solution On/Off Switch (U) and turn the key switch On. Continue to hold both switches
(Q) and Scrub Pressure Decrease (S) switches to scroll through the menus until "Scrub System" appears.
(R) to enter this submenu.
(S) until "Light Scrub Setting Adjustment" is shown on the display.
(R) to enter this submenu. Within this menu you can adjust Scrub Pressure, Solution Flow and Detergent