Stanley FATMAX SFMCD710 Traducido De Las Instrucciones Originales página 10

ENGLISH
Note: Do not change gears when tool is running. If you are
having trouble changing gears, make sure that the dual range
gear button is either completely pushed forward or completely
pushed back.
Screw driving
For driving fasteners, the forward/reverse button should
u
be pushed to the left.
Use reverse (button pushed to the right) for
u
removing fasteners.
Note: When moving from forward to reverse, or vice versa,
always release the trigger switch first.
Drilling
Use sharp drill bits only.
u
Support and secure work properly, as instructed in the
u
Safety Instructions.
Use appropriate and required safety equipment, as
u
instructed in the Safety Instructions.
Secure and maintain work area, as instructed in the
u
Safety Instructions.
Run the drill very slowly, using light pressure, until the hole
u
is started enough to keep the drill bit from slipping out of it.
Apply pressure in a straight line with the bit. Use enough
u
pressure to keep the bit biting but not so much as to stall
the motor or deflect the bit.
Hold the drill firmly with two hands, one hand on the
u
handle, and the other gripping the bottom around the
battery area or the auxiliary handle if provided.
DO NOT CLICK THE TRIGGER OF A STALLED DRILL
u
OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE
TO THE DRILL CAN RESULT.
Minimize stalling on breakthrough by reducing pressure
u
and slowly drilling through the last part of the hole.
Keep the motor running while pulling the bit out of a drilled
u
hole. This will help reduce jamming.
Make sure switch turns drill on and off.
u
Drilling in wood
Holes in wood can be made with the same twist drill bits used
for metal or with spade bits. These bits should be sharp and
should be pulled out frequently when drilling to clear chips
from the flutes.
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The cutting
lubricants that work best are sulphurized cutting oil.
LED work light (Fig H)
When drill is activated by pulling the trigger switch (1), the
integrated LED work light (7) will automatically illuminate the
work area.
10
(Original instructions)
Note: The work light is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Troubleshooting
Problem Possible cause
Unit will not start. Battery pack not
installed properly.
Battery pack
not charged.
Unit starts The switch has
immediately upon been left in the
inserting battery "on" position.
Battery pack will Battery pack not
not charge. nserted into charger.
Charger not
plugged in.
Surrounding air
temperature too hot or
too cold.
Unit shuts off abruptly. Battery pack has
reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
Maintenance
Your STANLEY FATMAX tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
Regularly clean the ventilation slots in your tool and
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
u
Do not use any abrasive or solvent-based cleaner.
u
Protecting the environment
Z
Separate collection. Products and batteries marked
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Possible solution
Check battery
pack installation.
Check battery pack
charging requirements.
The switch must be moved
to "off" to prevent the tool
from immediately starting
when battery is inserted.
Insert battery pack into
charger until LED lights.
Plug charger into a
working outlet.
Move charger and battery
pack to a surrounding
air temperature of above
45 °C or below +40.5 °C.
Allow battery pack to cool
down.
Place on charger and allow
to charge.