Idiomas disponibles
Idiomas disponibles
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.4 Battery capacity indicator (Fig. 7)
Press the button for the battery capacity indicator
(d). The battery capacity indicator (e) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too high. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
6.1 Operation (Fig. 4)
Each time before starting to work, use the fi lling
level indicator (5) to check if the magazine con-
tains any nails and that the magazine cover (3) is
properly closed.
Important!
Determine the required and optimum depth of
penetration of the nails by fi rst using a test work-
piece which is similar in structure and material
Anl_FIXETTO_18_50_N_SPK13.indb 18
Anl_FIXETTO_18_50_N_SPK13.indb 18
GB
thickness to the workpieces you want to join.
6.2 Triggering shots (Fig. 4)
The built-in trigger catch prevents the cordless
nailer from being triggered accidentally. As the re-
sult a shot can be triggered only when you press
the trigger catch (6) of the cordless nailer against
the material and actuate the trigger (1).
Single shot
Set the selector switch for single shot / repeat
shot (10) to single shot.
Place the cordless nailer with its trigger catch (6)
against the workpiece ready for nailing. Pull the
trigger (1) once and let it go again after each shot.
Repeat shot
Set the selector switch for single shot / repeat
shot (10) to repeat shot.
Pull and hold the trigger (1). When you place the
cordless nailer with its trigger catch (6) against
the workpiece it will now shoot repeatedly until
you release the trigger (1).
Important!
To prevent the cordless nailer from overheating,
you must take a break of 20 minutes after approx.
500 shots in repeat mode.
If the nail goes in too far or if it does not go in far
enough you can adjust the depth of penetration
with the depth adjuster (Fig. 9) (see section 6.4).
6.3 Jammed nails (Fig. 8)
If a nail becomes jammed in the tool, proceed as
follows:
•
Remove the battery from the tool.
•
Open the magazine cover (3).
•
Open the lever (8) and the cover plate (7).
•
Remove the jammed nail.
•
Close the cover plate (7) and the magazine
cover (3) again.
6.4 Adjusting the depth (Fig. 8)
The tool has a depth adjuster (Fig. 8 / Item 9) in
the form of a rotary knob. If you screw it in the
direction (+), the nails will be shot in deeper. If
you want to reduce the depth that the nails are
shot in, you have to screw the rotary knob in the
direction (-).
Important!
Use some test pieces.
- 18 -
07.10.2022 09:29:20
07.10.2022 09:29:20
