Idiomas disponibles
Idiomas disponibles
•
Each time before starting work, check that the
magazine cover is securely fastened (Fig. 1/
Item 3). Clean the equipment thoroughly and
immediately each time after it has been used.
•
Each time before starting work, check that the
trigger catch functions perfectly and that all
screws are securely fastened.
•
Never tamper with the stapler.
•
Never dismantle or block any parts of the
stapler such as e.g. a trigger catch.
•
Never carry out any "emergency repairs" with
unsuitable means.
•
Proper stapler maintenance is required at
regular intervals in accordance with the infor-
mation supplied by the manufacturer.
•
Take precautions to prevent anything which
would weaken or damage the equipment, e.g.
from
a) striking or engraving,
b) modifi cations which are prohibited by the ma-
nufacturer,
c) guiding on templates made of hard material,
e.g. steel,
d) pushing across the fl oor,
e) using as a hammer,
f)
any kinds of acts of violence.
5.1 Checking the trigger catch (Fig. 1)
Warning!
Remove the battery.
Check the trigger catch (6) each time before use.
The trigger catch must move freely without jam-
ming. The spring on the stapler head and trigger
catch must return the trigger catch to the released
initial position again. Never use the equipment if
the trigger catch is not working.
1. Remove the battery from the tool.
2. Remove the staples/nails from the magazine
(Fig. 2/Item 4).
3. Check that the trigger catch (6) can move up
and down freely.
4. Reinsert the battery in the tool.
5. Press the trigger catch (6) against the work-
piece without pressing the trigger (1). The
tool is not allowed to operate. Never use the
tool if it operates without the trigger (1) being
pressed. Risk of injury!
6. Remove the tool from the workpiece. The
trigger catch (6) must return to its released st-
arting position. Press the trigger (1). The tool
is not allowed to operate. Do not use the tool
if it operates. Risk of injury!
Anl_FIXETTO_18_50_N_SPK13.indb 17
Anl_FIXETTO_18_50_N_SPK13.indb 17
GB
7. Press the trigger catch (6) against the work-
piece and press the trigger (1); the tool will
operate.
5.2 Loading the nails (Fig. 2-4/Item 4)
Warning!
Remove the battery.
•
When you fill the magazine (4), make sure
that you hold the equipment in such a way
that the muzzle is pointed neither at yourself
nor at anyone else.
•
To fill the magazine, press the magazine re-
lease (2) and slide back the magazine cover
(3) as far as it will go (see Fig. 2).
•
Nails:
With the pointed end of the nails downwards,
press the nails against the lower edge and
push them to the front as shown in Fig. 3 and
4.
Important!
It must be possible to move the magazine slide
without applying much force. Watch out for jam-
med nails!
5.3 Charging the Li battery pack (Fig. 5-6)
1. Remove the battery pack (a) from the handle,
pressing the pushlock button (b) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(c) into the socket outlet. The green LED will
then begin to blink.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger
•
and the battery pack
to our customer service center.
- 17 -
07.10.2022 09:29:20
07.10.2022 09:29:20
