Idiomas disponibles
Idiomas disponibles
Slide lock adjustment (Fig.11)
To unlock the track arm, turn the track arm lock knob (6)
counterclockwise or clockwise.
Switch action (Fig.12)
Caution! Before plugging in the tool, always check to see that
the switch trigger (37) actuates properly and returns to the
"OFF" position when released.
To start the tool, press the switch trigger (37).
u
To stop the tool, release the switch trigger (37).
u
Warning: Never use tool without a fully operative switch
trigger. Any tool with an inoperative switch is HIGHLY
DANGEROUS and must be repaired before usage.
Electronic Function. Laser beam action (Fig.13)
Caution! When not in use, be sure to turn off the laser.
Never look into the laser beam directly; lase beam may injure
your eyes.
LASER RADIATION: DO NOT STARE INTO THE BEAM or
any CLASSII LASER PRODUCTS.
Before shifting the laser line or performing maintenance
adjustment, be sure to unplug the tool.
To turn on the laser beam, press the upper position (I) of
u
the switch .
To turn off the laser beam, press the lower position (O) of
u
the switch.
The laser line is factory adjusted so that it is positioned 1mm
from the side surface of the blade (cutting position).
Cleaning of the lens for the laser light
If the lens for the laser light becomes dirty, or sawdust ad-
heres to it in such a way that the laser line is no longer easily
visible, unplug the saw and clean the lens carefully with a
damp, soft cloth. Do not use solvents or any petroleum based
cleaners on the lens.
Note: When laser line is dim and almost or entirely invisible
because of the direct sunlight in the indoor or outdoor window
near your work area, relocate the work area to a place not
exposed to direct sunlight.
Note: All of the adjustments for the operation of this machine
have been carried out at the factory.
Caution: Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure. The use of optical instruments
with this product will increase eye hazard. Do not attempt to
repair or disassemble the laser. If unqualified persons attempt
to repair this laser product, serious injury may result. Any
repair required on this laser product should be performed by
authorised service centre personnel.
(Original instructions)
Installing or removing saw blade (Fig.14, Fig.15,
Fig.16)
Caution: Always be sure that the tool is switched off and un-
plugged before installing or removing the blade. Use only the
wrench provided (38) to install or remove the blade. Failure to
do so may result in over tightening or insufficient tightening of
the screw. This may result in injury.
Fig.15
To remove the blade, use cross screwdriver to loose the
u
screw (39) holding the centre cover by turning it counter-
clockwise and loosen the screw (29) counterclockwise, but
don't remove it.
Turn the centre cover (40) counterclockwise and raise the
u
blade guard.
Press the shaft lock (25) (Fig 14) to lock the spindle and
u
use the wrench (38) to loosen the screw (41) clockwise.
Then remove the screw (41), outflange (42) and blade
u
(30).
Note! When inner flange (43) is removed mistakenly, be sure
to install it on the spindle with its flat surface facing the motor.
Fig.16
To install the blade, mount it carefully onto the spindle, making
sure that the direction of the arrow on the surface of the blade
(30) matches the direction of the arrow (44) on the blade case.
Install the outer flange and screw, and then use the wrench
to tighten the screw securely counterclockwise while pressing
the shaft lock.
Dust bag (accessory) (Fig.17)
The use of the dust bag (5) makes cutting operations clean
and dust collections easy.
To attach the dust bag (5), fit it onto the dust nozzle(14).
u
When the dust bag (5) is about half full, remove it from the
u
tool and pull the fastener (45) out.
Empty the dust bag of its contents, tapping it lightly so as
u
to remove particles adhering to the insides which might
hamper further collection.
Note! If you connect a vacuum cleaner to your saw, more
efficient and cleaner operations can be performed.
Securing work piece (Fig.18)
Warning! It is extremely important to always secure the work
piece properly and tightly using a material clamp. Failure to do
so can cause the tool to be damaged and/or the work piece to
be destroyed. PERSONAL INJURY MAY ALSO RESULT. After
a cutting operation, DO NOT raise the blade until the blade
has come to a complete stop. When cutting a long work piece,
use supports (46) that are as high as the top surface level of
the turn table (18).
Caution! Do not rely solely on the vertical material clamp to
secure the work piece.
ENGLISH
15
