Outdoor Sensor Installation - Beretta POWER X 35 Manual Del Instalador

3 6 Outdoor sensor installation

The correct positioning of the outdoor sensor is of funda-
mental importance for proper climate control operation.
The sensor must be installed outside the building to be
heated, at approx. 2/3 the height of the NORTH or NORTH
WEST façade and far from flues, doors, windows and sun-
ny areas.
Fastening the outdoor sensor to the wall
- Unscrew the sensor protection box cover, turning it
anticlockwise to access the terminal board and fas-
tening holes
- Trace the fastening points using the box as a tem-
plate
- Remove the box and drill the holes for the 5x25 ex-
pansion plugs
- Fasten the box to the wall, using the two supplied
dowels
- unscrew the nut on the fair lead, and insert a bipolar
cable (with a cross section of 0.5 to 1mm
plied) to connect the probe to terminals 7 and 8 (see
the scheme in the chapter "Multi-row wiring diagram")
- connect the two cable wires to the terminal board
without identifying the polarities
- fully tighten the cable gland nut and close the protec-
tion box cover.
b
The sensor must be positioned on a smooth wall sec-
tion. If there are exposed bricks or irregular walls, an
area with a smooth contact must be prepared.
Correspondence table for all sensors
Measured temperatures (°C) - Resistive values of the sensors (Ω).
T (°C) R (°Ω) T (°C)
- 20 67739 - 1
- 19 64571 0
- 18 61568 1
- 17 58719 2
- 16 56016 3
- 15 53452 4
- 14 51018 5
- 13 48707 6
- 12 46513 7 - 11 44429 8
- 10 42449 9
- 9 40568 10
- 8 38780 11
- 7 37079 12
- 6 35463 13
- 5 33925 14
- 4 32461 15
- 3 31069 16
- 2 29743 17
, not sup-
2
R (°Ω) T (°C) R (°Ω) T (°C)
28481 18 13062
27279 19 12565
26135 20 12090
25044 21 11634
24004 22 11199
23014 23 10781
22069 24 10382
21168 25 9999
20309 26 9633 19489 27 9281
18706 28 8945
17959 29 8622
17245 30 8313
16563 31 8016
15912 32 7731
15289 33 7458
14694 34 7196
14126 35 6944
13582 36 6702
b
The maximum length of the connection between the
outdoor sensor and the control panel is 50 m. In the
case of connections with a cable length that exceeds
50 m, check compliance of the value read on the card
with a real measurement and adjust parameter 39 to
make any necessary correction.
b
The connection cable between the outdoor sen-
sor and the control panel must not have couplings.
If these are necessary, they must be watertight and
suitably protected.
b
Any channelisation of the connection cable must be
separated by live cables (230Vac).
R (°Ω) T (°C) R (°Ω)
37 6470 56 3426
38 6247 57 3319
39 6033 58 3216
40 5828 59 3116
41 5630 60 3021
42 5440 61 2928
43 5258 62 2839
44 5082 63 2753
45 4913 64 2669 46 4751 65 2589
47 4595 66 2512
48 4444 67 2437
49 4300 68 2365
50 4161 69 2296
51 4026 70 2229
52 3897 71 2164
53 3773 72 2101
54 3653 73 2040
55 3538 74 1982
ENGLISH
Fig. 13
T (°C) R (°Ω) T (°C) R (°Ω)
75 1925 94 1137
76 1870 95 1108
77 1817 96 1079
78 1766 97 1051
79 1717 98 1024
80 1669 99
81 1622 100
82 1577 101
83 1534 102 84 1491 103
85 1451 104
86 1411 105
87 1373 106
88 1336 107
89 1300 108
90 1266 109
91 1232 110
92 1199
93 1168
51
998
973
948
925 901
879
857
836
815
796
776
757