Idiomas disponibles
Idiomas disponibles
ARCHITECTURAL AND ENGINEERING SPECIFICATIONS
The powered loudspeaker system shall have a frequency response from 58 Hz to 17 kHz. The peak SPL with
inaudible distortion shall reach 127 dB with music as a source, when measured at a distance of 1M and driven
to full output capacity. The system shall utilize dual heavy-duty 15" Peavey
Peavey
RX
14 titanium diaphragm compression driver tweeter on a constant directivity horn. The nominal
®
™
radiation pattern shall be 60 degrees in the horizontal plane and 40 degrees in the vertical plane.
The powered loudspeaker system shall have a medium impedance input connector consisting of one combo
female XLR and 1/4" RTS phone jack on the rear panel. Output connections on the rear panel shall consist of
a 1/4" phone jack providing link-out, which provides a pre-level control signal for the use of linking multiple
PV
215D's in a line. A level control will be located next to the input jack. Next to the level control, a Contour
®
Switch pushbutton will provide some bass and treble lift when engaged for improved listening at low levels.
The system power amplifiers shall have an unfiltered frequency response of 20 Hz to 20 kHz which deviates
no more than +0, -3 dB up to rated power, a damping factor greater than 200 @ 1 kHz into 4 ohms, hum and
noise better than 90 dB below rated power, and typical THD and IMD of less than 0.5%. The amplifier shall
be capable of 400W continuous output into a 4 ohm nominal load and shall incorporate DDT
The enclosure shall be constructed of MDF-type wood panels and be covered in black carpet. A pair of metal
handles shall be provided on the sides. A black-coated perforated metal grille shall be provided for speaker
component protection. The cabinet shall incorporate 4 rubber feet for floor standing use.
The outside dimensions shall be 48.50" tall by 18.88" wide by 14.75" deep, and the weight shall be 79 lbs.
Power requirements shall be a dual voltage range of: 100 to 120VAC, and 220 to 240VAC, 50 - 60 Hz, with a
nominal power consumption of 370 watts. The voltage ranges shall be switch selectable on the rear panel.
The loudspeaker system shall be called a Peavey model PV
PEAVEY
PV
215D - SPECIFICATIONS
®
®
®
Enclosure: Peavey PV
215D
Frequency Range 1 meter on-axis, swept-sine in 1/2 Space
environment: -10 dB: 40 Hz to 21 kHz
Frequency Response 1 meter on-axis, swept-sine in 1/2 Space
environment: 58 Hz to 17 kHz (±3 dB )
Sensitivity: (1w/1m) 98 dB
Maximum Peak SPL: 127 dB
Transducer Compliment: Dual heavy-duty Pro 15 15" woofer with 2
3/8" voice coil & 50 oz. magnet
RX
™
14 1.4" titanium diaphragm dynamic compression driver, on a
Constant Directivity 60 X 40 horn.
Nominal Coverage Pattern: 60 degrees horizontal by 40 degrees
vertical
Electro-acoustic Crossover Frequency: 2.6 kHz
Input Connections: One combo female XLR/ 1/4" phone jack
providing balanced or unbalanced operation.
Enclosure Materials & Finish: Trapezoidal, black carpet covered
12mm MDF, black powder-coated full length perforated steel grille.
Mounting or Suspension: Four rubber feet for floor use.
NOTE: This unit is not designed for overhead suspension!
Dimensions (H x W x D):
Front: 48.50 in. x 18.88 in. x 14.75 in.
1232 mm x 480 mm x 375 mm
Rear: 48.50 in. x 11.25 in. x 14.75in.
1232 mm x 286 mm x 375 mm
Weight:
79 Lbs.
(35.9 kg)
Pro 15 model woofers, and a
®
215D.
®
ELECTRONICS AND AMPLIFIER SPECIFICATIONS:
Power Amp Rating, Total Power Output: 800 watts peak available
power, Continuous Power: 400 watts into 4 ohms @ less than 1%
distortion
Electronic Input Impedance (Nominal): 2.7 k ohms balanced (XLR or
1/4"), 1.35 k ohms unbalanced 1/4".
Infrasonic filter protection: 24 dB/octave roll-off
Nominal Amplifier Frequency Response: +0, -3 dB from 20 Hz to 20 kHz
Hum and Noise: Greater than 90 dB below rated power
DDT Dynamic Range: Greater than 14 dB
THD and IM: Typically less than 0.5 %
Damping Factor: Greater than 200 @ 1000 Hz, 4 Ohms
Power requirements of Peavey PV
Watts, Voltage and Frequency Ranges: 100-120 VAC, and 220 –
240VAC, at 50- 60 Hz
Fuse Type:
For 100-120 VAC USE: International fuse classification T6.3AL . In
the USA, types GDC, GMC, 215, 218, and 477 cartridge-style 5 x 20
mm size fuses with a 6.3 amp 250V rating can be used.
For 220-240 VAC USE: International fuse classification T3.15AL .
This is a cartridge style 5 x 20 mm size time-delay fuse with a 3.15
amp 250V rating.
compression.
™
®
2015D System: Nominal 370
