Idiomas disponibles
Idiomas disponibles
G2451
after the throttle has been released. Do not lay the
tool down until rotation has stopped
Observe that stored compressed air in the hose
►
may cause an accidental start
Release control device if the energy supply should
►
fail
Maintenance
Rust protection and internal cleaning
Water in the compressed air, dust and wear particles
cause rust and sticking of vanes, valves etc.
This can be solved by lubricating with oil (a few
drops), running the machine for 5-10 seconds and
wiping off excess oil with a cloth. Do this before
longer standstills.
Lubrication
The front motor ball bearing should be lubricated
with grease in conjuction with the regular overhaul
of the machine.
For flexible spindle extension – When fitting the
extended spindle – apply 0.5 cm
"Lubricating Engineers LE3752" (or EP grease) at
the bottom of the hole in the collet holder.
Lubricating guide
Use lubricants of good quality. The oils and greases
listed in the lubrication table are examples of lubric-
ants that can be recommended.
Brand
General purpose
Bearings
BP
Energrease LS-EP2
Castrol
Spheerol EP L2
Esso
Beacon EP2
Q8
Rembrandt EP2
Mobil
Mobilegrease XHP 222
Shell
Alvania EP2
Texaco
Multifak EP2
Molycote
BR2 Plus
Overhaul
T
WARNING Overspeed could result in serious
injury or death
If governor is used, check that correct governor
►
is assembled. Careless handling may put it out of
order
Do not disassemble security parts, e.g. speed
►
governor or overspeed shut-off. These parts must
be completely replaced when damaged
EN
3
of grease type
Air lubrication
Energol E46
Arox EP46
Chopin 46
Almo oil 525
Tonna R32
Aries 32
© Atlas Copco Industrial Technique AB - 9836 3077 01
Safety and operating instructions
Always check the free speed of the machine after
►
service. See Section Preparation before using the
die grinder
The entire machine should be checked regularly at
six-month intervals. If it is in heavy duty service or
not running properly it should be taken out of service
more often for inspection.
The strainer at the air inlet should be cleaned fre-
quently to prevent clogging and decreased capacity.
Useful information
C Log in to Atlas Copco www.atlascopco.com
You can find information concerning our products,
accessories, spare parts and published matters on our
website.
Ergonomic guidelines
) Take frequent breaks and change work positions
1
frequently.
) Adapt the workstation area to your needs and the
2
work task.
• Adjust for convenient reach range by determin-
ing where parts or tools should be located to
avoid static motion.
• Use workstation equipment such as tables and
chairs appropriate for the work task.
) Avoid work positions above shoulder level or with
3
static holding during assembly operations.
• When working above shoulder level, reduce
the load on the static muscles by reducing the
weight of the tool, using for example torque
arms, hose reels or weight balancers. You can
also reduce the load on the static muscles by
holding the tool close to the body.
• Make sure to take frequent breaks.
• Avoid extreme arm or wrist postures, particu-
larly for operations requiring a degree of force.
) Adjust for convenient field of vision by minimiz-
4
ing movement of the eyes and head during the
work task.
) Use the appropriate lighting for the work task.
5
) Select the appropriate tool for the work task.
6
) Use ear protection equipment in noisy environ-
7
ments.
) Use high-quality inserted tools or consumables to
8
minimize exposure to excessive levels of vibra-
tions.
) Minimize exposure to reaction forces.
9
• When cutting:
A cut-off wheel can get stuck if the wheel is
either bent or if it is not guided properly. Make
7
