Idiomas disponibles
Idiomas disponibles
4.
SAFETY CRITERIA
This equipment should only be used in accordance with the instructions
EN
described in this manual. Any other use is forbidden, since it may cause damages
to persons, machine or other objects
The usage of this product is intended exclusively to qualified operators according
to the standards in force.
Use this machine only for the purposes described on chapter "Fields of
Application" and according to its operator's manual.
Replace defective or worn-out parts only with Ritmo genuine spare parts.
Any intervention or repair on this product has to be carried out by qualified
operators.
SAFETY ALERTS
This hazard alert sign appears in this manual, when you see this
sign, carefully read what it says: YOUR SAFETY IS AT STAKE.
You will see the hazard alert sign with these words:
DANGER, WARNING, and CAUTION.
Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, may
result in minor or moderate injury.
In this manual you should look for two other words: NOTICE and IMPORTANT.
NOTICE: can keep you from doing something that might damage the machine
or someone's property. It may also be used to alert against unsafe practices.
IMPORTANT: can help you do a better job or make your job easier in some
way.
READ AND UNDERSTAND
Ritmo Manufacturing, cannot anticipate every possible circumstance that
might involve a potential hazard. The warnings in this manual and on the
machine are therefore not all inclusive. You must satisfy yourself that a
procedure, tool, work method, or operating technique is safe for you and
others. You should also ensure that the machine will not be damaged or made
unsafe by the method of operation or maintenance you choose.
ELECTRIC HAZARDS
Parts involved:
•
HOT IRON
•
DRILLING MACHINE
Check that the electric features of the machine correspond with those of the
power source.
The on-site board or the power unit to which the machine is connected must
be equipped with a high-sensitivity differential switch (I=30mA).
Do not expose the machine to rain or to any other liquids.
Make sure that all the accessories, implements, etc. used for protection (e.g.
gauntlets) are always completely dry.
Do not expose the cables to chemical agents, mechanical strain or general
hazards such as the passage of vehicles or passers-by, contact with sharp
objects, pulls, etc.
Unplug the machine when no longer in use or for temporary interruptions.
Before using the machine check that each single part is in perfect working
order, especially the insulating components like cables, cable leads and
pressers. Once monthly, check that the differential switch is in perfect
working order.
Clean the machine thoroughly at the end of each session. Do not use solvents,
petrol or any abrasive substances which might damage the
insulating parts.
Connect the machine to earth.
Check that the earth connection is operative.
12
Do not operate this equipment until you have
carefully read, and understand the "Safety" and
"Operation" sections of this manual, and all
other equipment manuals that will be used with
it. Your safety and the safety of others depends
upon care and judgment in the operation of this
equipment.
Follow all applicable federal, state, local, and
industry specific regulations.
If it becomes necessary to use an extension, the cable must
comply with the regulations in force and be suitable for the
power required.
SELV-powered equipment (extremely low safety voltage) is
required in narrow spaces, particularly damp places, sites surrounded by
metal structures or water (e.g. shipyards).
MECHANICAL HAZARDS
Parts involved:
DRILL PRESS
FITTING CHUCK
HOLE SAW
Keep at a safe distance while the carriage is in motion.
CATCHING
CRUSHING
ENTANGLING
HAZARD
HAZARD
HAZARD RELATED TO TEMPERATURE
Parts involved:
•
HEATING PLATE
Handle the heating plate with caution.
Extreme caution should be taken when cleaning the heating plate.
Do not touch the welded bead nor the surrounding areas until they have
cooled down completely.
BURNING
HAZARD
Parts involved:
•
HEATING PLATE
Do not use the machine if the area is at risk of explosion
due to the presence of flammable gases etc.
Keep outside the range of the heating plate any
flammable materials or those which may deteriorate in
the
heat (e.g. oils, solvents, paint, etc.).
TEMPERATURE CHECK
Incorrect setting of the thermoelement temperature can
lead to a bad welding result.
Periodically check with a calibrated digital thermometer
that the temperature of the thermoelement surfaces is
correct.
SPLINTERING
CUTTING
HAZARD
HAZARD
USE PROTECTIVE
GLOVES
FIRE HAZARD
