Idiomas disponibles
Idiomas disponibles
90565239 REV 1 PCL120ID 12 V Lithium Impact Driver.qxd:??????-00 Cir Saw book
QUICK RELEASE CHUCK (FIG. H)
WARNING:
Make certain the lock-off button is
engaged to prevent switch actuation before
installing or removing accessories.
NOTE: The chuck accepts 1/4 inch (6.35 mm) hex
accessories only.
Place the switch in the locked off (center) position
or remove battery pack before changing
accessories.
To install an accessory, pull the chuck collar (3)
away from the front of the tool, insert the
accessory, and release the collar. The accessory is locked in place.
To remove an accessory, pull the chuck collar (3) away from the front of the tool,
remove the accessory and release the collar.
ON BOARD BIT STORAGE
A magnetic bit storage slot (6) is built-in to the area on the top of the tool.
BELT CLIP
A belt clip (7) is provided which can be switched to either side of the tool.
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment. This Class B
digital apparatus complies with Canadian ICES-003.
THE RBRC™ SEAL
The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the
lithium-ion battery (or battery pack) indicates that the costs to recycle the battery (or
battery pack) at the end of its useful life have already been paid by
PORTER-CABLE.
RBRC™ in cooperation with PORTER-CABLE and other battery users, has established
programs in the United States to facilitate the collection of spent lithium-ion batteries.
Help protect our environment and conserve natural resources by returning the spent
lithium-ion battery to an authorized PORTER-CABLE service center or to your local
retailer for recycling. You may also contact your local recycling center for information on
where to drop off the spent battery.
RBRC™ is a registered trademark of the Rechargeable Battery Recycling Corporation.
H
3
10
6/25/10
2:41 PM
Page 10
Troubleshooting
Problem
Possible Cause
• Unit will not start.
• Battery pack not installed properly.
• Battery pack not charged.
• Battery pack will not charge. • Battery pack not inserted into charger. • Insert battery pack into
• Charger not plugged in.
• Surrounding air temperature
too hot or too cold.
• Unit shuts off abruptly.
• Battery pack has reached its
maximum thermal limit.
• Out of charge. ( To
maximize the life of the
battery pack it is designed
to shutoff abruptly when
the charge is depleted.)
For assistance with your product, visit our website at www.portercable.com for a list of
service centers, or call the PORTER-CABLE Customer Care Center at (888) 848-5175.
MAINTENANCE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
REPLACEMENT PARTS
Use only identical replacement parts. For a parts list or to order parts, visit our service website at
www.portercable.com. You can also order parts from your nearest PORTER-CABLE Factory
Service Center or PORTER-CABLE Authorized Warranty Service Center. Or, you can call our
Customer Care Center at (888) 848-5175.
SERVICE AND REPAIRS
All quality tools will eventually require servicing and/or replacement of parts. For information about
PORTER-CABLE, its factory service centers or authorized warranty service centers, visit our
website at www.portercable.com or call our Customer Care Center at (888) 848-5175. All repairs
made by our service centers are fully guaranteed against defective material and workmanship. We
cannot guarantee repairs made or attempted by others.
You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson,
Tennessee 38305, (888) 848-5175 - Attention: Product Service. Be sure to include all of the
information shown on the nameplate of your tool (model number, type, serial number, etc.).
ACCESSORIES
WARNING:
Since accessories, other than those offered by PORTER-CABLE,
have not been tested with this product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only PORTER-CABLE recommended
accessories should be used with this product. A complete line of accessories is
available from your PORTER-CABLE Factory Service Center or a PORTER-CABLE
Authorized Warranty Service Center. Please visit our Web Site www.portercable.com
for a catalog or for the name of your nearest supplier.
THREE YEAR LIMITED WARRANTY
PORTER-CABLE will repair or replace, without charge, any defects due to faulty
materials or workmanship for three years from the date of purchase for tools (two
years for batteries). This warranty does not cover part failure due to normal wear or
tool abuse. For further detail of warranty coverage and warranty repair information,
Possible Solution
• Check battery pack
installation.
• Check battery pack
charging requirements.
charger until green LED
appears.
• Plug charger into a
working outlet. Refer to
"Important Charging Notes"
for more details.
• Move charger and battery
pack to a surrounding air
temperature of above 40
degrees F (4.5°C) or below
105 degrees F (+40.5°C).
• Allow battery pack to cool
down.
• Place on charger and
allow to charge.
11
