Idiomas disponibles
Idiomas disponibles
RISK OF EYE INJURY.
RISK OF BURSTING.
RISK OF FIRE.
RISK TO BREATHING.
RISK OF INJURY.
RISK TO HEARING.
NOTE:
ELECTRICAL WIRING.
WARNING:
CAUTION:
To provide proper ventilation for cooling, the compressor must be kept a minimum of 12 inches (31 cm) from the nearest wall, in a well–ventilated area.
Restricting any of the compressor ventilation openings will cause overheating and could cause fire, never place objects against or on top of compressor.
On oil-lubed compressors, oil can leak or spill and could result in fire or breathing hazard. Oil leaks will damage paint, carpet or other surfaces in
vehicles or trailers. Always place the compressor on a protective mat when transporting to protect against damage to vehicle from leaks. Remove
compressor from vehicle immediately upon arrival at your destination.
WARNING:
Improper installation by unqualified personnel
can result in serious injury or death. Replacement and installation
must be performed by authorized service center personnel.
This air compressor pump is intended to be used as a replacement
pump on an existing air compressor system of similar performance. Use
of this air compressor pump in alternate applications will void the warranty
and potentially create unsafe operating conditions.
1.
Place flywheel on the crankshaft and attach with washers and bolt.
Torque bolt to 14-16 LB-FT. Verify correct flywheel rotation.
CAUTION:
Do not force flywheel onto the crankshaft.
2.
Position and assemble air compressor to the platform.
3.
Attach air filters to the pump heads.
This air compressor pump was shipped without oil in the
crankcase. Oil must be added before operation. Running the
pump without oil will void your warranty.
NOTICE: Risk of property damage. Use air compressor oil only. Multi-weight
automotive engine oils like 10W30 should not be used in air compressors.
They leave carbon deposits on critical components, thus reducing performance
and compressor life.
NOTE: Use synthetic blend, non-detergent air compressor oil.
200-2980
IMPORTANT SAFETY INSTRUCTIONS
Always wear ANSI Z87.1 approved safety goggles when using an air compressor. Never point any nozzle
or sprayer toward a person, animal or any part of the body. Equipment can cause serious injury if the spray
penetrates the skin.
•Do not use plastic or pvc pipe for compressed air. Use only galvanized steel pipe and fittings for compressed
air distribution lines.
Unattended operation of this compressor could result in personal injury or property damage. To reduce the risk
of fire, do not allow the compressor to operate unattended. Always disconnect electrical power by turning the
pressure switch to off and drain the tank daily or after each use.
Air obtained directly from the compressor should never be used to supply air for human consumption. The air
stream may contain carbon monoxide, toxic vapors, or solid particles from tank. Breathing these contaminant's
can cause serious injury or death. In order to use air produced by this compressor for breathing, suitable filters
and in-line safety equipment must be properly installed. In-line filters and safety equipment must be properly
installed. In-line filters and safety equipment used in conjunction with the compressor must be capable of
treating air to all applicable local and federal codes prior to human consumption.
Always operate the compressor in a stable secure position to prevent accidental movement of the unit. Never
operate the compressor on a table, workbench, roof or other elevated position. Use additional air hose to reach
high locations.
Always wear hearing protection when using an air compressor. Failure to do so may result in hearing loss.
Refer to the air compressor's serial label for the unit's voltage and amperage requirements. Ensure that all
wiring is done by a licensed electrician, in accordance with the National Electrical code.
CALIFORNIA PROPOSITION 65 WARNING: This product contains chemicals known to the State of California
to cause cancer, birth defects and/or reproductive harm. Wash hands after handling.
ASSEMBLY AND INSTALLATION
NOTE: Crankcase oil capacity is approximately 11.35 fluid ounces (335,7 ml).
4.
Unscrew the oil fill plug (E) and slowly add compressor oil until it is
between A and B (approximately 11.35 oz.). Note: When filling the
crankcase, the oil flows very slowly into the pump. If the oil is added too
quickly, it will overflow and appear to be full.
CAUTION:
Overfilling with oil will cause premature compressor
failure. Do not overfill.
A = Full
B = Add
C = Oil drain plug
D = Oil level sight glass
E = Oil fill plug
Fig. 1
E
D
C
3
