Idiomas disponibles
Idiomas disponibles
Removing the Battery
To remove the rechargeable battery, press the battery re-
lease button and pull the battery out. Do not use force to do
this.
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Changing the tool (see figure A)
The application tool may heat up significantly during
u
operation. Allow it to cool down before touching it.
The drill spindle is locked when the on/off switch (10) is not
pressed. This makes it possible to change the application
tool in the drill chuck quickly, conveniently and easily.
Open the keyless chuck (2) by turning it in the direction of
rotation ➊ until the tool can be inserted. Insert the tool.
Firmly tighten the sleeve of the keyless chuck (2) by turning
it by hand in the rotational direction ➋ until it stops clicking.
This will automatically lock the drill chuck.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Bosch Power Tools
Operation
Starting Operation
Setting the rotational direction (see figure B)
The rotational direction switch (9) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (10) is being pressed.
Right rotation: To drill and to drive in screws, press the ro-
tational direction switch (9) through to the left stop.
Left rotation: To loosen and unscrew screws, press the ro-
tational direction switch (9) through to the right stop.
Switching on/off
To start the power tool, press and hold the on/off switch
(10).
The LED (8) lights up when the on/off switch (10) is lightly
or fully pressed, meaning that the work area is illuminated in
poor lighting conditions.
To switch off the power tool, release the on/off switch (10).
Adjusting the speed
EasyDrill 18V-38:
You can adjust the speed of the power tool when it is on by
pressing in the on/off switch (10) to varying extents.
A light pressure on the on/off switch (10) results in a low ro-
tational speed. Increased pressure on the switch causes an
increase in speed.
Adjusting the Speed/Impact Rate
EasyImpact 18V-38:
You can adjust the speed/impact rate of the power tool when
it is on by pressing in the on/off switch (10) to varying ex-
tents.
Applying light pressure to the on/off switch (10) results in a
low rotational speed/impact rate. Applying increasing pres-
sure to the switch increases the speed/impact rate.
Preselecting the Torque
EasyDrill 18V-38:
The torque presetting ring (3) can be used to preselect the
required torque in 20 stages. When the correct setting is
used, the application tool will be stopped when the screw is
driven flush into the material or once the set torque has been
reached. In position
the overload clutch is deactivated,
e.g. for drilling.
When unscrewing screws, you can select a higher setting or
set the tool to the
symbol.
Preselecting the Torque
EasyImpact 18V-38:
The torque presetting ring (3) can be used to preselect the
required torque in 20 stages. When the correct setting is
used, the application tool will be stopped when the screw is
driven flush into the material or once the set torque has been
reached. In position
the overload clutch is deactivated,
e.g. for drilling.
English | 17
1 609 92A 8AW | (09.12.2022)
