Idiomas disponibles
Idiomas disponibles
12.- Attach the butterfly assembly (76) to the support (96)
aligning with point (c), remove the knob (18), adjust the
position and release the knob (18), Fig.12.
Place the shaft (98) in point (c), Fig.12, fit the screws (74)
and the washers (75), Fig.12.
13.- First attach the pulley (a) to the upper frame (20) using
the screw (109), the washer (11) and the nut (10), Fig.13, F.
Pass the cable (39) through the first pulley, leaving the
end of the cable on the right, Fig.13. The cable (39) must
be passed through each pulley each time a pulley is fitted.
When installing the pulleys (b), (c), first place the pulley
clamp (25) on both sides of the pulley and then fit the bolt
(109), the washer (11) and the nut (10), Fig.13, G.
Place the pulley (d) on the column (12) and fit the screw
(119), the washer (11) and the nut (10), Fig.13.
When installing the pulleys (e), (f), (g) place the powder
sleeve (99) on each side of the support (96), then place
the pulley and fit the screw (108), the washer (11) and the
nut (10), Fig.13, H.
Attach the pulley (h) to the upper frame (20) using the bolt
(102), the washer (11) and the nut (10), Fig.13, I.
When you finish passing the cable (39) through the last
pulley, place a pin to prevent it from coming out.
14.- Fit the screws (116), the washers (104) and the nuts
(101) on the support (96), Fig.14.
15.- Pass the cable (39) through the cover (41) and the
shaft (42) Fig.15.
Hook one end of the chain (44) to the shaft (42) and the
other end to the bar (77), Fig.15. Fix the other end of the
cable (39) to the selection rod (29), Fig.15.
16.- Pass one end of the cable (37) through the cover (41)
and the shaft (42) and fix the cable with the cover screw
(41), Fig.16. Put the pulley (i) on the column (12) and fit
the screw (119), the washer (11) and the nut (10), then
pass the cable (37) through the pulley. The other pulleys
use the screw (109), the washer (11) and the nut (10),
Fig.16. Pass the cable through the pulleys each time you
attach one.
To install the pulley (j) place the clamps (25) on each side
of the pulley and fit the screw (109), the washer (11) and
the nut (10).
When you finish passing the cable (37) through the last
pulley, pass the terminal through the cover (41) and the
shaft (42) and secure it with the cover screw (41), Fig.16.
17.- Use the hook (43) to fix the biceps rope (46) with the
shaft of the cable (42), Fig.17.
Hook the chain (44) with the hooks (43) to the pull bar (83)
on one side and to the cable shaft (42) on the other,
Fig.17.
18.- Pass the end of the cable (40) with the nut through
the spring (45) and fix it on the assembly (22), Fig.18.
Fix the pulley (32) on the support (25) using the screw
(109), the washer (11) and the nut (10), Fig.18.
Pass the cable (40) through the pulley, fit it with the hook
(43), Fig.18. Attach it to the structure (1) using the other
hook (43), Fig.18.
19.- Pass the end of the cable (38) through the cover (41)
and the shaft (42) and fix it with the cover screw (41),
Fig.19.
First put the pulley on the bracket (90) using the screw
(109), the washer (11) and the nut (10), then pass the
cable through the pulley. The other pulleys use the same
screws. Pass the cable through the pulleys each time you
mount one.
Place the pulleys (m) and (n) on the supports (22), Fig.19.
Put the pulleys (k) and (p) on the rear structure (21), you
only need the screw (109) to attach them, Fig.19.
Place the pulleys (l) and (o) on the frame (1), Fig.19.
When you finish passing the cable (38) through the last
pulley, pass the terminal through the cover (41) and the
shaft (42) and secure it with the cover screw (41), Fig.19.
20.- To fit the handles, pass the cable (38) through the
cover (41) and the shaft (42) and attach it to the hook (43),
Fig.20.
21.- Place the covers (52), (53), (54), (55) using the
screws (118) and the washers (105), Fig.21.
22.- Attach the left cover (48) and fix it to the upper frame
(20) and the base frame (1) using the screws (121) and
the washers (103), Fig.22.
23.- Place the right cover (49) and fix it to the upper frame
(20) and the base frame (1) using the screws (121) and
the washers (103), Fig.23.
Place the middle cover (50) and fit the screws (122) and
the washers (107), Fig.23.
Do not hesitate to get touch with the Technical Assistance
Service if you have any queries by phoning customer
services (see last page in manual).
BH RESERVES THE RIGHT TO MODIFY THE
SPECIFICATIONS OF ITS PRODUCTS WITHOUT
PRIOR NOTICE.
19
