Operation - Parkside PKS 1700 A1 Instrucciones De Utilización Y De Seguridad

Ingletadora telescópica
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

Anleitung_LB5_4300689:_
GB/
MT
7.2 Assembling the saw (Fig. 1-2, 4-6)
To adjust the turntable (16), loosen the
locking grip (13) by approx. 2 turns and
press the latched position lever (12) to
disengage the turntable (16) (Figure 4).
To release the saw from its bottom position,
apply light downward pressure to the
machine head (5). At the same time pull the
safety pin (25) out of the motor mount. Turn
the safety pin (25) through 90° so that the
saw remains unlocked (Fig. 1-2).
Swing the machine head (5) up until the
release lever (3) latches into place (Fig. 1).
Fit the clamping devices (8) on the left
and/or right side of the fixed saw table (17)
(Fig. 1).
Undo the locking screws for the workpiece
support (10) (Fig. 5).
Mount the workpiece support (9) on the
fixed saw table (17) and tighten the
appropriate locking screw (10) (Fig. 5).
Mount the second workpiece support (9) on
the opposite side of the saw and secure
with the appropriate locking screw (10).
When the locking screw (23) is loosened,
you can tilt the machine head (5) to the left
by up to 45° (Fig. 1-2).
Screw the additional stability bar (18) to the
back of the equipment (Fig. 6).
7.3 Precision adjustment of the stop for
crosscut 90° (Fig. 7-8)
No stop angle included.
Fasten the turntable (16) in 0° position.
Undo the locking screw (23) and move the
machine head (5) all the way to the right
using the handle (1).
Place the 90° angular stop (z) between the
blade (7) and the turntable (16).
Slacken the counternut (d). Adjust the
adjustment screw (90°) (31) until the angle
between the blade (7) and the turntable (16)
equals 90°.
Retighten the counternut (d) to secure this
setting.
Check the position of the pointer (21) on the
scale (20). If necessary, release the pointer
(21) with a crosstip screwdriver, move to the
0° position of the scale (20) and retighten.
68
21.12.2010
16:41 Uhr
Seite 68
7.4 Precision adjustment of the stop for
miter cut 45° (Fig. 1, 7, 10-11)
No stop angle included.
Fasten the turntable (16) in 0° position.
Undo the locking screw (23) and move the
machine head (5) all the way to the left
using the handle, until it coincides at 45°.
Place the 45° stop angle (y) between the
blade (7) and the turntable (16).
Adjust the adjustment screw (32) so that the
angle between the blade (7) and the
turntable (16) equals exactly 45°.

8. Operation

8.1 Cross cut 90° and turntable 0°
(Fig. 1-3, 12)
Important! The integral resetting springs will
automatically lift the machine head. Do not
simply let go of the handle (1) after cutting, but
allow the machine head (5) to rise slowly,
applying slight counter pressure as it does so.
For cutting widths up to approx. 100 mm it is
possible to fix the saw's drag function with the
locking screw for drag guide (24) in rear
position. If the cutting width exceeds 100 mm
you must ensure that the locking screw for drag
guide (24) is slackened and that the machine
head (5) can be moved.
Important. To make 90° crosscuts, the
adjustable stop rail (29) must be fixed at the
inner position.
Open the locking lever (30) for the
adjustable stop rail and push the adjustable
stop rail inwards.
The adjustable stop rail (29) must be fixed
far enough in front of the innermost position
that the distance between the stop rail (29)
and the saw blade (7) amounts to a
maximum of 5mm.
Before making a cut, check that the stop rail
(29) and the saw blade (7) cannot collide.
Secure the locking lever (30) again.
Move the machine head (5) to its upper
position.
Use the handle (1) to push back the
machine head (5) and fix it in this position if
Tabla de contenido
loading

Tabla de contenido