Idiomas disponibles
Idiomas disponibles
en
ENGLISH
Feed direction
Always work in the opposite direction. Always push
the machine forwards as shown. See fig. B.
The direction of rotation of the cutter is indicated by
an arrow (13) on the machine.
Guide the machine evenly at a speed suitable for
the material being processed.
7.3
Putting down after use
After ending the cutting process, switch off the
machine and only set it down when the motor has
come to a standstill.
7.4
Special working methods:
Cutting with parallel guide (fig. C)
1. Attach the parallel guide (14) with screws (11) on
the machine.
2. Undo the wing screw (a) and adjust the distance
to the cutter. Tighten the wing screw (a).
Stop with guide bearings (see fig. D)
The stop with guide bearings (15) is used for cutting
along a curved edge
1. Attach the stop (15) with the screw (11) to the
machine.
2. Undo the clamping screw (a).
3. Using the adjusting screw (b), set the desired
distance to the cutter.
4. Tighten the clamping screw (a).
Template follower (see fig. E)
For cutting according to a template fixed on the
workpiece.
1. Undo the screws (a) to remove the footplate (8).
Insert the template follower (16) and then screw
the footplate (8) back on.
2. Attach a template (b) on the workpiece (c). Place
the machine on the template and guide it so that
the template follower (16) glides along the edge
of the template (b).
Milling along a strip attached to the workpiece
/ milling along a straight marking
1. Attach a strip on the workpiece and guide the
machine with a straight edge of the foot plate
along the strip. (Always use the same edge.)
Profile milling
1. When working with profile cutters, first remove a
larger chip and then a smaller chip.
2. The feed rate must not be too low, otherwise the
wood will scorch and the cutter will become
prematurely blunt.
8. Cleaning, Maintenance
Unplug power cable.
Dust deposits must be regularly removed from the
machine. This includes vacuum cleaning the
ventilation louvres on the motor.
9. Troubleshooting
Restart protection:
The machine does not start. Restart protection is
12
active. If the mains plug is inserted with the machine
switched on or if the power supply is restored
following an interruption, the machine does not start
up. Switch the machine off and back on again.
10. Accessories
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
For the complete range of accessories, see
www.metabo.com or the main catalogue.
11. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
A defective mains cable must be replaced only with
a special, original mains cable from Metabo
available from the Metabo service.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
12. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Packaging materials must be disposed of according
to their labelling in accordance with municipal
guidelines. Further information can be found at
www.metabo.com in the "Service" section.
Only for EU countries: never dispose of
power tools in your household waste!
According to European Directive 2012/19/EU
on Waste from Electric and Electronic Equipment
and implementation in national law, used power
tools must be collected separately and recycled in
an environmentally-friendly manner.
13. Technical specifications
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
P
= Rated input
1
P
= Power output
2
n
= Idle speed
0
n
= Speed at rated load
1
H
= max. stroke height
max
D
= max. permissible diameter of the cutter
max
m
= Weight without mains cable
Note: The diameter of the collet bore of the collet
chuck can be found on the nameplate of the
machine.
Measured values determined in conformity with
EN 62841.
Machine in protection class II
