Idiomas disponibles
Idiomas disponibles
Stop the mower and always unplug the safety key and
remove the batteries. Clean the exterior of the machine
thoroughly using a soft brush and cloth. Do not use
water, solvents or polishes. Remove all grass and debris,
especially from the ventilation slots.
Turn the machine on its side and clean the blade area. If
grass cuttings are compacted in the blade area, remove
with a wooden or plastic implement.
Store the machine in a dry place. Do not place other
objects on top of the machine.
To aid storage, Press and hold quick-release button and
fold the handle bar.
MAINTENANCE
WARNING: Stop the mower and unplug the safety
key and remove the batteries before removing the
grass collection bag.
NOTE: To ensure long and reliable service, perform the
following maintenance procedures regularly. Check for
obvious defects such as a loose, dislodged or a damaged
blade, loose fittings, and worn or damaged components.
Check that the covers and guards are all undamaged and
are correctly attached to mower. Carry out any necessary
maintenance or repairs before operating mower. If the
mower should happen to fail despite regular maintenance,
please call our customer helpline for advice.
BLADE SHARPENING
KEEP BLADE SHARP FOR BEST MOWER
PERFORMANCE. A DULL BLADE DOES NOT CUT
14
GRASS CLEANLY OR MULCH PROPERLY.
WEAR PROPER EYE PROTECTION WHILE
EN
REMOVING, SHARPENING, AND INSTALLING
BLADE. ENSURE THAT SAFETY KEY IS
REMOVED.
Sharpening the blade twice during a mowing season
is usually sufficient under normal circumstances. Sand
causes the blade to dull quickly. If your lawn has sandy
soil, more frequent sharpening may be required.
REPLACE BENT OR DAMAGED BLADE
IMMEDIATELY.
WHEN SHARPENING THE BLADE (See Fig. K)
1. Make sure blade remains balanced.
2. Sharpen blade at the original cutting angle.
3. Sharpen cutting edges on both ends of blade to keep
it balanced, removing equal amounts of material from
both ends.
NOTE:
1. Be sure the mower is turned off and unplug the safety
key, remove the batteries.
2. Place the mower in stand up storage mode.
BLADE BALANCING (See Fig. L)
Check balance of blade by placing center hole in blade
L-1 over a screwdriver shank L-2, clamped horizontally
in a vise L-3. If either end of the blade rotates downward,
file that end. Blade is properly balanced when neither end
drops.
BLADE MAINTENANCE (See Fig.M1, M2)
Replace your Mower Blade after 50 hours mowing or 2
years, which ever is the sooner-regardless of condition.
Follow these procedures to remove and replace the
Blade. You will need garden gloves (not provided) and a
spanner wrench (not provided) to remove the Blade. Make
sure safety key and batteries are not installed. Wedge a
block of wood between the blade and the mower deck
to prevent the blade from turning and unscrew the Blade
Bolt counter-clockwise using a spanner wrench, and then
remove the Blade.
To re-assemble, position the Blade with the cutting edges
towards the ground. Then securely tighten the Blade Bolt.
TROUBLESHOOTING
PROBLEM
SOLUTION
1. Mower doesn't
A. Check to make sure safety
run when Operating
key has been installed and is
Bail is activated.
fully seated and thatSafety
lock-out button is being
completely pushed.
B. Release Operating Bail to
turn mower off. Unplug the
safety key and remove the
batteries, turn mower over
and check that blade is free
to turn. If not free, return to
an authorized servicer. Blade
should turn freely.
C. Has battery been fully
charged? Plug in charger and
wait for green light to come
on. For starting, press both
the Safety lock-out button and
the Operating bail at the same
time. (See Fig. E1)
2. Mower doesn't
A. To activate self-propel,
run when Self-
press both the Safety lock-out
propel Speed-
button and the Self-propel
Control Lever is
speed-control lever at the
activated.
same time. (See Fig. F)
3. Motor stops while
A. Release Operating Bail to
mowing.
turn mower off. Unplug the
safety key and remove the
batteries,turn mower over
and check that blade is free
to turn. If not free, return to
an authorized servicer. Blade
should turn freely.
B. Raise cutting height of
wheels to highest position and
start mower.
C. Has battery been fully
charged? Plug in charger and
wait for green light to come
on.
D. Avoid overloading the
mower. Slow down the cutting
pace by pushing mower
slower or raise the cut height.
Or both.
