Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

SERIN
®
WALL MOUNT FAUCET
IN-WALL LAVATORY FITTING
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
To ensure that your installation proceeds smoothly-please
read these instructions carefully before you begin.
ROUGHING-IN DIMENSIONS
8"
(203mm)
CROSS
HANDLE
HOT
1/2" NPT INLETS
2-1/8" D.
(54mm)
Required Tools
Tubing Cutter
1
INSTALL VALVE BODY
Determine where the finished wall location will be. This measurement
is very important! Note: The rough-in measurement from the finished
wall is; 2" minimum and 3" maximum. This is a 1" tolerance. See
rough-in illustration above.
Secure FAUCET BODY (1) to cross brace of wall structure
at required height using two wood screws.
Connect HOT water supply to left VALVE inlet and COLD water
supply to right VALVE inlet. Use pipe sealant or Teflon tape for
all threaded connections. For sweat connections, do not make
sweat connections directly to valve body. Damage to seals and
and valve cartridge may occur.
Turn valves to off position. Turn hot and cold supplies on and
check fitting connections for leaks .
Complete wall construction.
4"
(102mm)
FINISHED
COLD
(51mm) MAX.
2" MAX.
1-1/4" O.D.
(32mm) O.D.
Adjustable Wrench
Channel Locks
Turn off hot and cold water
CAUTION
supplies before beginning.
Installation
Instructions
2064.451
2" MIN.
(51mm)
WALL
2" D.
(52mm)
Plumbers' Putty or
Caulking
WALL STUDS
Certified to comply with ASME A112.18.1M
U.S. Patent No. 5,819,789
M968852 Rev.1.6 (5/19)
3" MAX.
(76mm) MAX.
1"
(25mm)
2" D.
(52mm)
FINISHED
WALL
9-1/4"
(235mm)
Pipe Wrench
Teflon Tape
Flat Blade Screwdriver
CROSS BRACE
WOOD SCREWS
1
16"
HOT
COLD
Tabla de contenido
loading

Resumen de contenidos para American Standard SERIN 2064.451

  • Página 5: Grifo Para Montaje En Pared Accesorio Para Lavabo De Pared

    ® 2064.451 GRIFO PARA MONTAJE EN PARED ACCESORIO PARA LAVABO DE PARED Gracias por elegir American Standard, referente de calidad durante más de 100 años. Conformidad certificada con la norma ASME A112.18.1M Para asegurarse de realizar la instalación sin inconvenientes, Patente de EE.UU.
  • Página 6: Instalación Del Caño De Pared

    INSTALACIÓN DEL CAÑO DE PARED Retire los PROTECTORES DE YESO (1) de los cuerpos de válvula. Compruebe que la JUNTA TÓRICA DE LA BOQUILLA DEL CAÑO (2) esté colocada en la ranura de la BOQUILLA DEL CAÑO (3). Enrosque el SOPORTE DEL CAÑO (4) en la BOQUILLA DEL CAÑO (3). Alinee la ranura del SOPORTE DEL CAÑO (4) con la superficie de la pared acabada.
  • Página 7: Prueba Del Grifo Instalado

    SERVICIO Para cambiar la dirección de rotación del mando, realice lo siguiente: Gire la válvula a la posición de cierre. Enrosque la BASE DEL MANDO (1) hacia la izquierda para extraer el CONJUNTO DEL MANDO (2) de la BASE DEL CHAPETÓN (3). Utilice un destornillador de punta plana para extraer PARA EXTRAER el SUJETADOR DE PRESIÓN (4).
  • Página 8: Grifo De Lavabo Para Montaje En La Pared

    SERIN ® GRIFO DE LAVABO PARA MONTAJE EN LA PARED NÚMERO DE MODELO 2064.451 M962423-YYY0A JUEGO DE CHAPETÓN DEL CAÑO 994053-0070A CARTUCHO 617852-0070A ADAPTADOR M970004-0070A JUEGO DE AIREADOR 918555-0070A (1.2 GPM) TORNILLO DEL MANDO 621423-0070A ALOJAMIENTO DE VÁLVULA M962424-YYY0A JUEGO DE CHAPETÓN DEL MANDO M950245-YYY0A CONJUNTO DEL MANDO Reemplace las “YYY”...

Tabla de contenido